Derbi servicemanual - Scootergrisen

More documents

Recommendations

Info

STRIPPING - Remove the luggage carrier ( 4 screws). - In PADDOCK models separate the electrical connectors on the turn indicators. - The left hand footrest cover (1 screw). - The left hand side panel (2 screws). - The right hand footrest cover (1 screw). - The right hand side panel (2 screws). - Raise the saddle. - Remove the side panels (5 screws). - Remove the oil reservoir cap. - Remove the fuel tank filler cap. - Remove the anti-freeze reservoir cap on PAD- DOCK-LC models. - Remove the helmet carrier box (6 screws). - Remove the rear brake cable nut. - Remove the rear brake guide stop (1 screw). - Remove the engine earth screw. - Remove the throttle cable union. - Disconnect the electrical connectors for the magneto, the stop light, the choke, the starter, the high tension coil and the coil earth cable. - On the LC models, also disconnect the thermocontact spade connector. - Disconnect the two pipes from the connector on the carburettor: the fuel pipe and the vacuum line. - Disconnect the oil hose at the reservoir outlet. - In PADDOCK-LC models extract the antifreeze drain plug. - Remove the cooling hoses where they connect to the antifreeze reservoir. - Remove the 2 fixing screws which secure the engine to the frame. - Remove the 1 shock absorber screw. - Separate the engine from the frame. 10 WITHDRAWING THE ENGINE FROM THE FRAME
STRIPPING THE ENGINE - Remove the exhaust pipe. - Remove the filter box together with the inlet pipe and the rear mudguard. - Withdraw the rear wheel nut and remove the rear wheel. - Withdraw the centre stand spring, the pin, the central shaft, and the stand. - On PADDOCK-LC models, remove all hose clips, radiator hoses, and the radiator. - Remove the fan (2 screws). - Remove the sleeve cover. - On PADDOCK-LC models, first withdraw the antifreeze outlet connector on the cylinder head (2 screws and gasket). - Remove the carburettor together with the reed valve (4 screws). - Remove the magneto nut using the special tool 0.0G.0.530.001.1. - Remove the magneto using the special magneto extractor tool 0.0G.053.0.015.1. 11
Page 1: This manual has been prepared by DE
Page 4 and 5: Engine Number of cylinders ........
Page 6 and 7: 6 REGULAR MAINTENANCE TABLE Períod
Page 8 and 9: HUNTER MODELS Stripping the fork le
Page 12 and 13: - Remove the stator (2 screws): in
Page 14 and 15: - In order to extract the water pum
Page 16 and 17: - Assembly of the wheel shaft beari
Page 18 and 19: - Measure the lateral play at the c
Page 20 and 21: Stripping - Unscrew the water pump
Page 22 and 23: - The working surfaces of the pulle
Page 24 and 25: - Fit the clutch hub onto the pulle
Page 26 and 27: - Fit the oil pump with 2 screws 5
Page 28 and 29: - The cylinders of the monobloc mod
Page 30 and 31: Stripping the carburettor - Remove
Page 32 and 33: Carburettors Make Dell’orto Dell
Page 34 and 35: - Fit the cooling hose from the wat
Page 36 and 37: GENERAL CHARACTERISTICS Component B
Page 38 and 39: Charging the battery for the first
Page 40 and 41: SCHEMATIC AND IGNITION CIRCUIT CONT
Page 42 and 43: Connection of lighting switch, turn
Page 44 and 45: SCHEMATIC AND CARBURETTOR HEATING C
Page 46 and 47: 46 ECHEMA ELECTRIQUE HUNTER Orange
Page 48 and 49: ANNEXE PREDATOR-LC - CAT - WVTA Mod
Page 50 and 51: TORQUE SETTINGS PART NAME TORQUE SE
Page 52 and 53: For all ATLANTIS models, hydraulic
Page 54 and 55: ATLANTIS LC: - Hydraulic shock abso
Page 56 and 57: CHECKING THE IGNITION Inspecting th
Page 58 and 59: CYLINDER HEAD Compression Ratio: 11
Page 60 and 61:
Adjustment Table BRAND CARBURETOR M
Page 62 and 63:
CHECKING THE ELECTRICAL SYSTEM IN T
Page 64 and 65:
65 ECHEMA ELECTRIQUE PREDATOR Orang
Page 66 and 67:
67 ECHEMA ELECTRIQUE ATLANTIS Orang
Page 68 and 69:
ECHEMA ELECTRIQUE ATLANTIS (USA) D
Page 70 and 71:
ECHEMA ELECTRIQUE ATLANTIS 100 D F
Page 72 and 73:
74 SPECIAL TOOLS Description Refere
Page 74 and 75:
76 SPECIAL TOOLS Description Refere
Page 76 and 77:
DESCRIPTION TORQUE SETTING Nw x m C
Page 78 and 79:
Suspension stroke .................
Page 80 and 81:
Starter motor - The securing nuts a
Page 82 and 83:
SYMBOL 84 LUBRICATE GREASE QUANTITY
Page 84 and 85:
Movil semi pulley - Remove the thre
Page 86 and 87:
Clutch - Remove the central nut whi
Page 88 and 89:
Re-assembly of the clutch - Refit t
Page 90 and 91:
Follower pulley shaft oil seal - St
Page 92 and 93:
Mating the crankcase halves - Apply
Page 94 and 95:
Thermostat - cylinder head - by-pas
Page 96 and 97:
SYMBOL 98 LUBRICATE GREASE QUANTITY
Page 98 and 99:
Disassembling the seal Common tools
Page 100 and 101:
SYMBOL 102 LUBRICATE GREASE QUANTIT
Page 102 and 103:
SYMBOL 104 LUBRICATE GREASE QUANTIT
Page 104 and 105:
Piston Caution! Position the arrow
Page 106 and 107:
Piston Rings - The verification of
Page 108 and 109:
Crankshaft alignment check - Using
Page 110 and 111:
Checking the voltage regulator - Br
Page 112 and 113:
114 ECHEMA ELECTRIQUE GP1 Orange Gr
Page 114:
116 ECHEMA ELECTRIQUE GP Series D F
show all

Derbi servicemanual - Scootergrisen

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?