AerospaceIndustry - Frank Drucklufttechnik

More documents

Recommendations

Info

SP-1300-4-EN-0105-.25M Self Colleting Tools 4-1
Introduction Self Colleting Tools Our self colleting drills provide rapid cycle times while producing quality holes and accurate countersinks. With stroke capacity from 1 inch to 3 inches, power capacity from 0.85 hp to 2.0 hp, and a full range of speeds, these self colleting tools are ideal for drilling and countersinking aircraft skin. Aluminum, laminates, and mixed stacks of aluminum or laminate over titanium or steel are well suited to the superb hole making capacity of these machines. Operation Workpiece Template Skinclamp 1.Position and clamp the drilling template on the workpiece. 2.Drill the first hole by conventional means. Insert Collet Locate Template Boss 3.Insert the Collet into the first hole and locate the Template Boss in the drilling template. Insure that the Collet/Mandrell extends through the workpiece. The drill/countersink cycle is automated, maximizing productivity with single trigger control. Each of these tools uses a variation of an expanding collet to clamp or fixture in a tooling plate or to clamp directly to he workpiece. This economizes Template Boss and simplifies the fixturing required to mont and locate these tools. In the case of the variable spacing foot (also known as the template foot), the collet/mandrel is inserted into a predetermined hole in the workpiece. The template 4.Depress the trigger. Immediately, the Mandrel is drawn back and the Collet locks the tool to the work. Simultaneously, the motor starts and the tool feeds forward to a positive stop. The tool then retracts automatically and returns to its starting position. 5.Release the trigger; the motor shuts off and unclamping occurs. 6.Reposition the Boss and drill other holes within the colleting Range. 7.Withdraw the Collet/Mandrell and insert into a recently driled hole. Repeat steps 3 through 6. boss is inserted into a template hole with the boss face on the workpiece. When the the tool first clamps by expanding the collet on the mandrel. The tool automatically feeds to a preset depth, and then automatically retracts. After retracting, the tool unclamps. Remaining in the same clamping location, the tool can then be moved to the next clamp location and the process repeated. In the case of the jig collet and concentric collet, the expanding collet is co-axial with the tool spindle. The tool feeds to a preset depth, then automatically trigger is actuated, Standoff Pad Depth Adjustment C-Clamp Foot Doler P3 with Variable Spacing Foot Motor Module Variable Spacing Foot Mandrel Feed Rate Adjustment Collet Foot Pad (Adjust per curvature of workpiece) Straight Hole Jig Collet Foot Tooling Tapered Hole Hole Hole dia. dia. Tooling Plate Stand-off Workpiece 5° Taper retracts. After retracting, the tool unclamps. The tool is then moved to the next location and the process is repeated. In addition to the variable spacing foot, concentric collet, and jig collet foot, the C-clamp configuration is also available. This configuration is ideal for applications near the edge of surfaces. Fixture Plate Fixture holes may overlap. Minimum center distance= 0.75 of hole diameter Fixture plate hole dia.= Colleting dia. +0.003”/-0.000” Fixture Plate thickness “T” should equal the Collet length. 4-2 4-3 Jig Collet Foot Feed Rate Adjustment Workpiece “T” Collet Length Standoff Concentric Collet Tooling Doler P3 with Concentric Collet Depth Motor Module Adjustment Concentric Collet Foot Actuator Arm
Page 1 and 2:
SP-1300-EN-0205-2.5M Q U A L I T Y
Page 3 and 4: I-1 ISO 9001 Quality System Certifi
Page 5 and 6: I-5 Cooper Power Tools Advanced Dri
Page 7 and 8: I-9 Sales & Service Centers www.coo
Page 9 and 10: I-13 Safety Recommendations - Safe
Page 11 and 12: SP-1300-1-EN-0105-.25M In-Line Posi
Page 13 and 14: 1-4 In-Line Tools 15QD-S125 Series
Page 15 and 16: In-Line Tools In-Line Tools 158QGDA
Page 17 and 18: In-Line Tools In-Line Tools 15QDA-S
Page 19 and 20: In-Line Tools In-Line Tools 158QGDB
Page 29 and 30: 1-36 In-Line Tool Accessories 230QG
Page 31 and 32: Cooper Power Tools P.O. Box 1410 Le
Page 33 and 34: Introduction Right Angle Positive F
Page 35 and 36: Right Angle Tools Right Angle Tools
Page 37 and 38: 2-10 Right Angle Tools 158QGD-15RAB
Page 43 and 44: Right Angle Tools Accessories Right
Page 45 and 46: SP-1300-3-EN-0105-.25M Peck Feed Dr
Page 47 and 48: 3-4 Peck Drills HT3 Series Capacity
Page 49 and 50: 3-8 Peck Drills 120QP-21500 Self Fe
Page 51 and 52: Peck Drills Accessories Peck Drills
Page 53: Peck Drills Accessories Drill Point
Page 57 and 58: Doler ® Self Colleting Machines* D
Page 59 and 60: Doler ® Self Colleting Machines Do
Page 61 and 62: Doler ® Self Colleting Machines* D
Page 63 and 64: Doler Self Colleting Machines Acces
Page 65 and 66: Doler ® Self Colleting Machines Do
Page 67 and 68: 4-26 Doler ® Self Colleting Machin
Page 69 and 70: Quackenbush ® Self Colleting Machi
Page 79 and 80: 4-50 Notes Notes 4-51
Page 81 and 82: SP-1300-5-EN-0105-.25M Specialty To
Page 83 and 84: 5-4 Specialty Tools 10QNPD Nut Plat
Page 85 and 86: Specialty Tools Specialty Tools CD
Page 87 and 88: 5-12 Specialty Tools Back Spotfacer
Page 89 and 90: Cooper Power Tools P.O. Box 1410 Le
Page 91 and 92: 6-2 Cutters A11N B51-Q C31-M D22-T
Page 93 and 94: 6-6 Cutters Cutter Mounting Styles
Page 95 and 96: SP-1300-7-EN-0105-.25M Recoules Mic
Page 97 and 98: Microstop Drill-Cage Microstop Dril
Page 99 and 100: 7-8 Microstop Drill-Cage RB 256 M6
Page 101 and 102: 7-12 Ball Type Microstop Drill-Cage
Page 103 and 104: 7-16 Ball Type Microstop Drill-Cage
Page 105 and 106:
7-20 Microstop Drill-Cage RB 406 M1
Page 107 and 108:
7-24 Microstop Drill-Cage for Drill
Page 109 and 110:
Page 111 and 112:
Page 113:
Cooper Power Tools P.O. Box 1410 Le
show all

AerospaceIndustry - Frank Drucklufttechnik

Create successful ePaper yourself

Delete template?

Save as template?