AerospaceIndustry - Frank Drucklufttechnik

More documents

Recommendations

Info

Quackenbush ® Self Colleting Machines Quackenbush ® Self Colleting Machines 136SC-150 Q-Matic Self-Colleting Drill Motor Drill Capacity: .25” (6.4mm) Countersink Capacity: .5” (12.7mm) Feed Stroke: 1.5” (30mm) Clamp Stroke: .5625” (14.3mm) Motor, clamp and retract mechanism are airoperated; feed rate is controlled by external hydraulic feed control cylinder. Semi-automatic self-colleting tool has automatic clamp/drilI/retract cycle. 136 series motor develops .85 nominal horsepower. Model Optional mist lubricatorintroducescoolant and air blast to cutter. Booster pump accessory increases both clamp and feed pressures. Distance between collet and drill is variable from .5 in. (12.5 mm) to 2.75 in. (70 mm). Tool has trigger lock to allow tool to cycle without operator attention. Tool remains clamped to workpiece until operator releases trigger. 136SC-150-TF Stroke Weight w/steel foot Feed Rate Spindle Variable Distance Inlet Minimum Feed Collet lbs kg Speeds (RPM) Collet to Drill Hose Size 136SC-150 1.5 in .5625 in .05 to 40 in/sec 8.0 3.6 400, 900, 2100, 3100, Min: .5 in (12.7mm) .375” NPT .5” (30mm) (14mm) 1.25 to 10 mm/sec 6000, 7800, 11,500, Max. 2.75 in (70mm) (12.7mm) 22,500 Rated tool performance at 90 PSIG measured at toll inlet with motor running. INFORMATION REQUIRED FOR ORDERING SELF-COLLETING DRILL: 1. TOOL RPM 2. TYPE SPINDLE REQUIRED (Exact information concerning the cutter to be utilized in the drilling application must be provided in order to determine the proper spindle configuration. A drawing of the cutter should be provided for each application.) 3. FOOT TYPE REQUIRED: • Template Foot Right Hand OR Left Hand • Jig Collet Foot Depth Sensing OR Non-Depth Sensing • Drill Lock Bushing Foot 21000 series OR 22000 Series Bushing 4. TOOLING INFORMATION • Template Foot Models Template Boss (see page 4-37) Collet/Mandrel Assembly (see page 4-37) • Jig Collet Foot Models For depth sensing models, the stand-off distance (see page 4-35) must be provided. Collet/Mandrel Assembly (see page 4-37) 136SC Q-MATIC SELF-COLLETING DRILL WITH DEPTH SENSING JIG COLLET FOOT INFORMATION REQUIRED TO ORDER JIG COLLET FOOT TOOLS: (1) Specify tooling plate hole size—diameter A or B— in order to determine collet size (see standard collet size chart). (2) When ordering depth sensing models, specify stand-off distance. (Top of tooling plate to work surface) (3) When ordering for straight hole tooling plates, specify tooling plate thickness. Drill Lock Bushing Foot The versatile Q-Matic 136SC Drill is available with a foot which accepts standard 21000 and 22000 series lock-type drill bushings. This foot design increases the versatility of the Q-Matic Drill so that it may be locked onto the rigid tooling plate using various drill bushing tips and their accessories. Drill Jig Collet Foot The 136SC Q-Matic Drill is available with a jig collet foot, either with or without a depth sensing sleeve, for use with rigid tooling plates which have STRAIGHT or BACK TAPERED locating holes. This attachment, with a built-in sensing sleeve, will sense variations up to .125” in the distance between the work surface and the top of the tooling plate, which allows production drilling of holes with countersink to precise limits. A port has been provided in the foot to deliver coolant to the drill point. STANDARD COLLET SIZES Straight Tapered Hole Hole A dia. .B dia. Depth Sensing 1.000 .796 .875 .670 Non-Depth Sensing 1.000 .796 .875 .670 .750 .640 .625 .500 Special collets available upon request. 4-32 4-33
Quackenbush ® Self Colleting Machines Quackenbush ® Self Colleting Machines 136SC-150 Q-Matic Self-Colleting Drill Motor Booster Pump Assembly For increased clamping and feed force, an optional Booster Pump (Part No. 621482) is available. The pump provides extra clamp and feed when required. The Booster Pump assembly will increase both clamp and feed forces by a factor of 2.5. Mist Lubricator Assembly A mist lubricator assembly is available to introduce coolant and air to the cutter. The lubricator is actuated by air from the accessory air tap on the motor side and only functions when the motor is running. The standard mist lubricator (Part No. 631878) can be filled with a hand pump. The optional mist lubricators (Part No. 631879 and 631880) are filled by a pressure pump. BOOSTER PUMP Standard Large Manual Fill 631878 Pressure Fill 631879 631880 MIST LUBRICATOR TEMPLATE BOSS NOTE: TEMPLATE BOSSES ARE OPTIONAL AND ARE TO BE SPECIFIED BY CUSTOMER IF REQUIRED. Collets and Mandrels Collets and Mandrels are supplied as standard equipment with each tool and must be specified when ordered. Typical Configuration of Collets for hole sizes up to .250 in. (TO FIT HOLE IN TEMPLATE) (TO FIT COUNTERSINK DIAMETER ON CUTTER) INFORMATION NECESSARY TO ORDER COLLETS AND MANDRELS HOLE SIZE AND COLLET LENGTH CODE EXAMPLE; Application is to drill a .250 dia. hole in .500 thick material using a template with a thickness of .125 in. SELECT Template Boss (See Template Boss Length information above). This application requires a.150 length. Using Material Thickness Grip Range chart based on .500 material thickness, the collet and mandrel Length Code is EITHER -40 or -63 ORDER: 250-40 or .250-63 collet/mandrel Hole Collet Size Length Code (TEMPLATE BOSS LENGTH IS .150.) Typical Configuration of Mandrels for hole sizes up to .250 in. Template Boss Application Template Boss Part No. B C Template Sink Code Hole Dia. Dia. No. .434 .271 623573 .434 .286 623574 .434 .317 623575 .497 .271 623576 .497 .286 623577 .497 .317 623578 .497 .349 623579 .497 .380 623580 .622 .317 623581 .622 .349 623582 .622 .380 623583 .622 .411 623584 .622 .489 623585 .622 .505 623586 Material Thickness Grip Range Temp. Boss Collet Length .150 Length Code* Series 1000 Standard Collets .00 - .37 – 23 .18 - .62 – 40 .43 - .87 – 63 .68 - 1.12 – 90 4-34 4-35 05/06/02
Page 1 and 2:
SP-1300-EN-0205-2.5M Q U A L I T Y
Page 3 and 4:
I-1 ISO 9001 Quality System Certifi
Page 5 and 6:
I-5 Cooper Power Tools Advanced Dri
Page 7 and 8:
I-9 Sales & Service Centers www.coo
Page 9 and 10:
I-13 Safety Recommendations - Safe
Page 11 and 12:
SP-1300-1-EN-0105-.25M In-Line Posi
Page 13 and 14:
1-4 In-Line Tools 15QD-S125 Series
Page 15 and 16:
In-Line Tools In-Line Tools 158QGDA
Page 17 and 18:
In-Line Tools In-Line Tools 15QDA-S
Page 19 and 20: In-Line Tools In-Line Tools 158QGDB
Page 25 and 26: In-Line Tools In-Line Tools 400QGDA
Page 27 and 28: In-Line Tools In-Line Tools 230QGDA
Page 29 and 30: 1-36 In-Line Tool Accessories 230QG
Page 31 and 32: Cooper Power Tools P.O. Box 1410 Le
Page 33 and 34: Introduction Right Angle Positive F
Page 35 and 36: Right Angle Tools Right Angle Tools
Page 37 and 38: 2-10 Right Angle Tools 158QGD-15RAB
Page 43 and 44: Right Angle Tools Accessories Right
Page 45 and 46: SP-1300-3-EN-0105-.25M Peck Feed Dr
Page 47 and 48: 3-4 Peck Drills HT3 Series Capacity
Page 49 and 50: 3-8 Peck Drills 120QP-21500 Self Fe
Page 51 and 52: Peck Drills Accessories Peck Drills
Page 53 and 54: Peck Drills Accessories Drill Point
Page 55 and 56: Introduction Self Colleting Tools O
Page 57 and 58: Doler ® Self Colleting Machines* D
Page 59 and 60: Doler ® Self Colleting Machines Do
Page 61 and 62: Doler ® Self Colleting Machines* D
Page 63 and 64: Doler Self Colleting Machines Acces
Page 65 and 66: Doler ® Self Colleting Machines Do
Page 67 and 68: 4-26 Doler ® Self Colleting Machin
Page 69: Quackenbush ® Self Colleting Machi
Page 73 and 74: Quackenbush ® Self Colleting Machi
Page 79 and 80: 4-50 Notes Notes 4-51
Page 81 and 82: SP-1300-5-EN-0105-.25M Specialty To
Page 83 and 84: 5-4 Specialty Tools 10QNPD Nut Plat
Page 85 and 86: Specialty Tools Specialty Tools CD
Page 87 and 88: 5-12 Specialty Tools Back Spotfacer
Page 89 and 90: Cooper Power Tools P.O. Box 1410 Le
Page 91 and 92: 6-2 Cutters A11N B51-Q C31-M D22-T
Page 93 and 94: 6-6 Cutters Cutter Mounting Styles
Page 95 and 96: SP-1300-7-EN-0105-.25M Recoules Mic
Page 97 and 98: Microstop Drill-Cage Microstop Dril
Page 99 and 100: 7-8 Microstop Drill-Cage RB 256 M6
Page 101 and 102: 7-12 Ball Type Microstop Drill-Cage
Page 103 and 104: 7-16 Ball Type Microstop Drill-Cage
Page 105 and 106: 7-20 Microstop Drill-Cage RB 406 M1
Page 107 and 108: 7-24 Microstop Drill-Cage for Drill
Page 113: Cooper Power Tools P.O. Box 1410 Le
show all

AerospaceIndustry - Frank Drucklufttechnik

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?