AerospaceIndustry - Frank Drucklufttechnik

Doler ® Self Colleting Machines* Doler ® Self Colleting Machines
P3 Drill with Variable
Spacing Foot
Thrust and power to drill up to .750”
diameter hole with a .930” countersink in
aluminum or a .500” diameter hole with a
.750” countersink in titanium.
Variety of spindle speeds and
terminations to satisfy a wide range of
applications
Infinite feed rate control
Drill point lubrication
Positive depth stop for countersink accuracy
Rigid and precise spindle for excellent hole quality and finish
Compact and Light weight
Low noise
Good balance and comfortable grip
Rotating cutter/countersink guide for maximum cutter life and hole quality
P3 3 2 – 16 E 2 – 2 2 W
FEED STROKE
2 = 2” Stroke
3 = 1.25” Stroke
4 = 3” Stroke
SPINDLE SPEED (X)
0 = 480 RPM 3 = 3600 RPM 6 = 6800 RPM
1 = 725 RPM 4 = 3000 RPM 8 = 2500 RPM
2 = 1050 RPM 5 = 5200 RPM 9 = 320 RPM
FOOT ATTACHMENT (XX)
15 = ”101” LH Variable Spacing Foot
16 = “101” RH Variable Spacing Foot
17 = “100” LH Variable Spacing Foot
18 = “100” RH Variable Spacing Foot
SPINDLE (X)
A = Erickson 200 Collet Chuck
B = Erickson 200 Collet Chuck with Coolant Spindle
D = .25-28 x 0.375 “Spacematic”
E = .25-28 x 0.500 “Spacematic”
F = .25-28 x 0.625 “Spacematic”
P = .375-24 x 0.500 Piloted External Thread (P.E.T.)
Q = .375-24 Piloted External Thread (P.E.T.)
with through the spindle coolant
*Note: Complete Check Sheet on page 4- 00
before placing order.
‡ Must specify Drill and Collet size when placing
order
SPECIFICATIONS:
Air Consumption: 35 scfm (1.0 HP)
65 scfm (2.0 HP)
Air Inlet Size: .375 NPT (1.0 HP)
.5 NPT (2.0 HP)
Recommended
Hose Size: .5” I.D. (1.0 HP)
.75” I.D. (2.0 HP)
Thrust: 320 lbs. @ 80 psig; w/booster 575lbf.
Depth Accuracy: Repeatable within .001”
Weight: P32 - 14.9 lbs.
P33 - 13.7 lbs.
P34 - 16.2 lbs.
Capacity - Diameter
Aluminum -.75 hole (18mm) with .930 (25mm)
countersink
Titanium - .50 hole (13mm) with .75 (18mm)
countersink
BOOSTER
B = Booster
Leave blank
for none
DEPTH
ADJUSTMENT (X)
W = Wrenchless
COLLET PILOT DIAMETER (X)
1 = .323 Pilot
2 = .437 Pilot
3 = .471 Pilot
CUTTER GUIDE DIAMETER (X)‡
1 = .375 Diameter 5 = .650 Diameter
2 = .500 Diameter 6 = .930 Diameter
3 = .625 Diameter 9 = Other, specify
4 = .750 Diameter
MOTOR POWER (X)
1 = One Horsepower
2 = Two Horsepower (Speed codes 6, 8, & 9 are not available.)
OPTIONAL EQUIPMENT (see pages 4-18 thru 4-26)
Template Boss
Clamping Collet/Mandrel
Foot Pad
Erickson 200 Collet
EXTRA COST ACCESSORIES (See pages 4-20 thru 4-22)
Drill Point Lubricator
Handling Ring
Venturi Vacuum
Vacuum Adapter
Dimensional Data - P3 Drill with Variable Spacing Foot
HEAVY DUTY COLLETS AND MANDRELS
Collets and Mandrels are available to accomodate virtually any hole
diameter and material thickness.
Each size can clamp on thickness variations of .4”.
Refer to page 4-22 for a complete list of heavy duty Collets and Mandrels.
Attachment No. Hole Spindle Offset
Left-Right Right-Left Spacing Range Side-To-Center
4-12 4-13
Operation
Workpiece
Skinclamp
1. Position and clamp
the drilling template
on the workpiece.
Model
Template
10.4
10.9
2. Drill the first hole by
conventional means.
Feed Rate
Adjustment
Insert
Collet
Locate
Template
Boss
3. Insert the Collet into
the first hole and
locate the Template
Boss in the drilling
template. Insure that
the Collet/Mandrell
extends through the
workpiece.
P32 = 15.1
P33 = 12.8
P34 = 18.1
1.00 Motor Module
Adjustability
Depth Adjustment
4. Depress the trigger. Immediately, the Mandrel is drawn
back and the Collet locks the tool to the work.
Simultaneously, the motor starts and the tool feeds
forward to a positive stop. The tool then retracts
automatically and returns to its starting position.
5. Release the trigger; the motor shuts off and unclamping
occurs.
6. Reposition the Boss and drill other holes within the
colleting Range.
7. Withdraw the Collet/Mandrell and insert into a recently
driled hole. Repeat steps 3 through 6.
Variable Spacing Foot Specifications
100 80-419 80-405 1.0-5.6 .75
101 80-478 80-479 1.0-5.6 .75
The 100 VSF is at a right angle to the P3 handle and is preferred in open areas.
The 101 VSF is approximately 45° from the P3 handle and is preferred in confined areas.
Air Inlet
Motor Module
Varies according
to Template Boss
.08
.83
Template Boss
Mandrel
Collet
Foot Pad