Xbase 09 Operating Manual - Cyborgstudio.com

More documents

Recommendations

Info

LFO Intensity LFO Intensity determines the intensity with which the LFO will modulate its target. LFO intensity is displayed as a numeric value between 0 and 127. To switch off an LFO, set the value to 0. Should you not be able to set the value to 0, hold the ACCENT button pressed and turn the knob counterclockwise until the display reads 0. LFO Frequency LFO Frequency sets the frequency (relative to the sequencer tempo) i. e. the LFO speed. The frequency is displayed as a numeric value between 0 and 127. NOTE: The absolute LFO frequency depends on the current sequencer tempo. In this wise, it is also possible to generate modulations with a free running LFO. LFO Synchronisation This parameter determines wether the LFO restarts at every programmed instrument step or if it freewheels past the instrument triggers. The display reads: FrE = freewheeling LFO SYn = beat synchronized LFO Select a setting by turning the "pulse" or "noise tune" knobs. To store your LFO page edits, press ENTER. This stores all LFO settings for the currently selected pattern. LFOs are active in Pattern and in Perform modes. Abort by pressing SHIFT. In this mode you select the patterns with different instrument control settings for each step. These are displayed as “P xx” (pattern number 1-64) The instrument’s sound control knobs influence the sound of the individual steps indirectly in the various Pattern Edit modes. For further details, see "Perform Mode" section. Page 28 XBase 09 Operating Manual
6.4.12 Track Page The Track Page contents three further sequencertracks. Their data is sended out via Midi-Out socket to control external Midi-soundgenerators directly from XBase09 internal sequencer. Every track can have its individual Midi-channel. Notenumber and -length is adjustable for every single step. Even accent-setting is possible. So up to three different melodielines or chords up to three notes can be programmed. Programming the steps is the same procedure like programming drumtracks, described in Pattern- Mode ( chapter 6.3, P.18). When sequencertracks are added to existing drumpatterns, the drumpatterns will not be changed in any way. To edit Midichannel, Notenumber and -length, the first four knobs of every instrument-section (BD, SD, HH) have a ‘page two’-function : 1. Tune = Note 2. Pitch = Octave 3. Decay = Midichannel 4. Harmonics = Notelength The knobs of Snaredrum- and HiHatsection are changing in the equal way. Now, we describe the programming procedure of a sequencertrack : �� hit PATT button patternmode active LED ligths up �� hit UP/DOWN or 1-16 buttons choose pattern display shows patternnumber �� hit SHIFT,then TRACKPAGE button sequencer active display shows ‘ trC ’ for ‘track’ �� hit WRITE button sequencer ‘sharp’ LED ligths up �� hit INSTRUMENT-button select track BD=1,SD=2,CH=3 LED lights up �� move knob 3 select midichannel display shows midich.-number �� move knob 4 select notelength display shows ‘ Stac ‘ or ‘ Leg ‘ -Staccato: every step is triggert -Legato: following steps are connected � hit STRART button sequenzer started � set steps described in chapter 6.3 P.18 Use Induvidual Step Mode (6.3.1) to assign different notes to individual steps. Use Track Record Mode (6.3.2 ) to assign same note to all steps. By moving knobs 1 and 2 , you can change your melodies in realtime. To get ‘musical’ results this way, you might need some practice. � move knob 1 and 2 assign notes and octave display shows note and trackno. when sequencer is running and reaching a step ‘ E - 1’ � Happy with your first track ??? � hit WRITE button Trk.Rec.Mode off LED stops flashing � hit WRITE, then INSTRUMENTbutt. select next track � move knob 3 select midichannel � and so on... programm new track like above . � Happy with all your tracks ??? � hit ENTER button pattern is stored, RampPage left XBase 09 Operating Manual Page 29
Page 1 and 2: XBase 09 Operating Manual 9 Softwar
Page 3 and 4: Contents Page 1. Introduction 05 1.
Page 5 and 6: 1. INTRODUCTION 1.1 Introducing the
Page 7 and 8: 2. CONNECTING THE XBASE 09 Before y
Page 9 and 10: 3.0 Quick start guide Turn unit on
Page 11 and 12: Push the Bass Drum pad and -while h
Page 13 and 14: 4. Detailed description 4.1 The Con
Page 15 and 16: sound. It is possilble to set both
Page 17 and 18: 4.2.7 WRITE This button switches be
Page 19 and 20: 5. PERFORM MODE Press the PERF butt
Page 21 and 22: 6. PATTERN MODE You get into Patter
Page 23 and 24: In Perform and Pattern Play modes,
Page 25 and 26: NOTE: If you want to shift some ste
Page 27: The first five knobs of the bass dr
Page 31 and 32: 7.2.3 Repeat (CLOSED HI HAT button)
Page 33 and 34: 9. Controlling the Xbase09 via MIDI
Page 35 and 36: 11. Midi Implementation 11.1 Sound
Page 37: 12. Technical Data Instruments Bass

Xbase 09 Operating Manual - Cyborgstudio.com

Create successful ePaper yourself

Delete template?

Save as template?