MAN-C24-0001 - Güralp Systems Limited

More documents

Recommendations

Info

CMG-CD24 2. Right-click in the white panel beneath Server, and select Add TCP Server.... 3. Input the IP address of the CD24, followed by a colon and then the output port 10002. For example: 192.168.33.2:10002 Click OK. 4. After a short wait, an entry for the digitiser should appear in the pane. Right-click on the entry and select Connect. 5. If the connection is successful, you should see blocks appearing in the Block Rx pane and streams will appear in Scream!'s main window. Close the Network Control window. 24 Issue C
Operator's Guide 3 Configuration & Control with Scream! Scream! distinguishes between configuration and control of digitisers. The most important difference is that a digitiser (and its attached instrument) may be controlled through Scream! at any time while it is acquiring data, whereas configuration options only take effect after a reboot (with consequent loss of data.) 3.1 The Configuration dialogue To change the configuration of any connected digitiser: 1. Locate the digitiser you want to configure. All connected digitisers have an entry in the tree on the left of Scream!'s main window. If the digitiser is transmitting data through a remote server or EAM, you may need to “unroll” the entry for that server (by clicking on the icon) to see the digitisers connected to it. 2. Right-click on the digitiser's entry (not the icon for the server or any ComXX icon). Digitisers are shown with icons depicting a coloured cylinder. 3. Click Configure.... Scream! will then contact the digitiser and retrieve its current configuration, a process which will take a few seconds. Once done, the Configuration setup window will be displayed. 4. Once you are happy with any changes you have made in the Configuration Setup window, click UPLOAD to send them to the digitiser and reboot. This will take a short while. Note: After uploading, allow up to 1 minutes for the digitiser to re-boot and resume transmitting data. To control a digitiser whilst it is running, either right-click on the digitiser's entry in the list and click Control..., or double-click the entry. In either case Scream! will contact the digitiser to retrieve control information and display the Control window. The options you can control immediately are: • the type of sensor you are using • GPS power cycling options March 2011 25
Page 1 and 2: CMG-CD24 Compact Digitiser Operator
Page 3 and 4: Operator's Guide 5 Command line int
Page 5 and 6: Operator's Guide 7.2.4 Triggering s
Page 7 and 8: Operator's Guide Once connected to
Page 9 and 10: Operator's Guide At this location,
Page 11 and 12: Operator's Guide Connect the wire f
Page 13 and 14: Operator's Guide The first few stat
Page 15 and 16: Operator's Guide 10. A Wi-Port entr
Page 17 and 18: Operator's Guide connect several CD
Page 19 and 20: Operator's Guide standard Güralp S
Page 21 and 22: 2.5 Downloading data over FireWire
Page 23: Operator's Guide 4. Select the Reco
Page 27 and 28: Operator's Guide generated by the d
Page 29 and 30: Operator's Guide criteria are met.
Page 31 and 32: Operator's Guide The Ratio column d
Page 33 and 34: Operator's Guide The spectral ampli
Page 35 and 36: Operator's Guide an internal buffer
Page 37 and 38: Operator's Guide Usually, the trans
Page 39 and 40: Operator's Guide Each channel calib
Page 41 and 42: Operator's Guide Separate from thes
Page 43 and 44: Operator's Guide You can retrieve b
Page 45 and 46: Operator's Guide FIFO mode will con
Page 47 and 48: 3.3 Digitiser status streams Operat
Page 49 and 50: 4 Calibrating the CD24 4.1 Calibrat
Page 51 and 52: Operator's Guide 10. The script wil
Page 53 and 54: 5 Command line interface 5.1 FORTH
Page 55 and 56: Operator's Guide 5.2.2 BAUD Syntax:
Page 57 and 58: Operator's Guide synchronize its in
Page 59 and 60: Operator's Guide 5.4 Output configu
Page 61 and 62: Operator's Guide The value at each
Page 63 and 64: Operator's Guide whilst lower rate
Page 65 and 66: Operator's Guide For example, 4 10
Page 67 and 68: Operator's Guide Enabling external
Page 69 and 70: Operator's Guide 5.7 Actions N/S 4
Page 71 and 72: Operator's Guide The flash memory i
Page 73 and 74: Operator's Guide 5.8.4 ALL-TIMES Sy
Page 75 and 76:
Operator's Guide that were recorded
Page 77 and 78:
Operator's Guide 5.9.7 HEARTBEAT Sy
Page 79 and 80:
Operator's Guide The first lines gi
Page 81 and 82:
6 Updating the CD24 Operator's Guid
Page 83 and 84:
Operator's Guide 7. To check that t
Page 85 and 86:
Operator's Guide Field COILCONST CA
Page 87 and 88:
Operator's Guide VPC=2.013,2.028,2.
Page 89 and 90:
Operator's Guide The Trigger Out re
Page 91 and 92:
Operator's Guide recent data. Any e
Page 93 and 94:
Operator's Guide 7.2.4 Triggering s
Page 95 and 96:
Operator's Guide The diode between
Page 97 and 98:
Operator's Guide 7.3.1.2 FireWire p
Page 99 and 100:
Operator's Guide 7.3.1.4 Sensor inp
Page 101 and 102:
Operator's Guide 7.3.2.2 Breakout b
Page 103 and 104:
7.4 Appendix D - Advanced network c
Page 105 and 106:
Operator's Guide From the main menu
Page 107 and 108:
Operator's Guide 4. The Wifi commun
Page 109 and 110:
Operator's Guide You will then be p
Page 111 and 112:
Operator's Guide Now click on “Se
Page 113 and 114:
Operator's Guide 7.6 Appendix F - S
Page 115 and 116:
8. Use DeviceInstaller to find the
Page 117:
8 Revision history Operator's Guide
show all

MAN-C24-0001 - Güralp Systems Limited

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?