TL-WR542G User Guide - TP-Link

More documents

Recommendations

Info

TL-WR542G 54Mbps Wireless Router User Guide 2. Access the AP's Web-based utility and configure the AP under Bridge mode, then input 00-13-56-A8-9E-1A in corresponding Blank. ‣ Enable Wireless Security – The wireless security function can be enabled or disabled. If disabled, the wireless stations will be able to connect the router without encryption. It is recommended strongly that you choose this option to encrypt your wireless network. The encryption settings are described below. ‣ Authentication Type - You can select one of the following authentication types: • WEP - Select WEP authentication type based on 802.11 authentications. • WPA-PSK/WPA2-PSK - Select WPA/WPA2 authentication type based on pre-shared passphrase. • WPA /WPA2 - Select WPA/WPA2 authentication type based on Radius Server. ‣ Authentication Options - You can select one of the following authentication options: • When you select WEP for authentication type you can select the following authentication options: • Automatic - Select Shared Key or Open System authentication type automatically based on the wireless station request. • Shared Key - Select 802.11 Shared Key authentication. • Open System - Select 802.11 Open System authentication. • When you select WPA-PSK/WPA2-PSK for authentication type you can select Automatic, WPA –PSK or WPA2-PSK as authentication options. • When you select WPA/WPA2 as an authentication type you can select Automatic WPA or WPA2 as authentication option. ‣ WEP Key Format - You can select ASCII or Hexadecimal format. ASCII Code Format stands for any combination of keyboard characters in the specified length. Hexadecimal 31
TL-WR542G 54Mbps Wireless Router User Guide format stands for any combination of hexadecimal digits (0-9, a-f, A-F) in the specified length. ‣ WEP Key settings - Select which of the four keys will be used and enter the matching WEP key information for your network in the selected key radio button. These values must be identical on all wireless stations in your network. ‣ Key Type - You can select the WEP key length (64-bit, or 128-bit, or 152-bit) for encryption. "Disabled" means the WEP key entry is invalid. • For 64-bit encryption - You can enter 10 hexadecimal digits (any combination of 0-9, a-f, A-F, zero key is not permitted) or 5 ASCII characters. • For 128-bit encryption - You can enter 26 hexadecimal digits (any combination of 0-9, a-f, A-F, zero key is not permitted) or 13 ASCII characters. • For 152-bit encryption - You can enter 32 hexadecimal digits (any combination of 0-9, a-f, A-F, zero key is not permitted) or 16 ASCII characters. ‣ Encryption - When you select WPA-PSK/WPA2-PSK or WPA/WPA2 for Authentication Type you can select Automatic, TKIP or AES as Encryptions. Figure 4-16 WPA-PSK/WPA2-PSK ‣ WPA-PSK/WPA2-PSK Passphrase - You can enter a WPA or WPA2 passphrase between 8 and 63 characters long. ‣ Group Key Update Period - Specify the group key update interval in seconds. The value can be either 0 seconds or from 30 seconds and up, 1-29 seconds are not usable figures. Enter 0 to disable the update. 32
Page 1 and 2: TL-WR542G 54M Wireless Router Rev:
Page 3 and 4: FCC STATEMENT This equipment has be
Page 5: National Restrictions 2400.0-2483.5
Page 8 and 9: CONTENTS Chapter 1. Introduction...
Page 10 and 11: TL-WR542G 54Mbps Wireless Router Us
Page 90:
TL-WR542G 54Mbps Wireless Router Us
show all

TL-WR542G User Guide - TP-Link

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?