Advantech HPC-1420-ISSE User Guide

More documents

Recommendations

Info

2.7 SAS/SATA backplane cabling Connects 8-pin Connect CPU/system fan cables power plug CON2_FAN CON4_FAN56 CON6_FAN910 CON1_FAN CON3_FAN34 CON5_FAN78 CON7_FAN1112 3 PCI bridge cards Port0 Port1 Port2 Port3 Connects SAS/SATA2 hard disk drive The system fans run in full speed during POST. 2-22 Chapter 2: Hardware Setup
2.8 Remove components Before install/uninstall devices,you might need to remove the pre-installed components in the system. This section tells you how to remove/install the components. 1. System fans 2. Device fans 3. Redundant PSU and power backplane board 4. SAS/SATA2 Backplane and bridge cards 5. Optical drive 6. Motherboard 2.8.1 System fans The system provides the follow fan sets: · Five 40mm x 56mm 15500rpm fans (Dual-fans for unit) · Two 40mm x 28mm 15500rpm fans Refer to the figure below for the location of the fans. 40mm x 56mm system fans 40mm x 28mm devices fan assembly Improper installation of the fan assembly might cause CPU overheat or system shut down. HPC-1420-ISSE User Manual 2-23
Page 1 and 2: HPC-1420-ISSE 1U DP Xeon HPC system
Page 3 and 4: 2.7 SAS/SATA backplane cabling.....
Page 5 and 6: 7.2.1 Windows 2000/Server 2003 ....
Page 7 and 8: Safety information Electrical Safet
Page 9 and 10: Conventions To make sure that you p
Page 11 and 12: CHAPTER 1 Product Introduction
Page 13 and 14: 1.2 System specifications The HPC-1
Page 15 and 16: 1.3 Front panel features The barebo
Page 17 and 18: 1.6 LED information 1.6.1 Front pan
Page 19 and 20: CHAPTER 2 Hardware Setup
Page 21 and 22: 5. Push the front side of the top c
Page 23 and 24: ® 2.2 Install the CPU and heatsink
Page 25 and 26: The CPU fits in only one correct or
Page 27 and 28: Rank population DIMM 32 DIMM 31 DIM
Page 29 and 30: 2.4 Hot-swap hard disk drives To in
Page 31 and 32: 2.5 Expansion slots 2.5.1 Installin
Page 33 and 34: 2.5.3 Remove the expansion cards To
Page 35 and 36: 2. Using a screw driver to secure t
Page 37 and 38: Standard interrupt assignments IRQ
Page 39: 2.6.1 Serial Port cable The system
Page 43 and 44: 2.8.2 Device fans The system comes
Page 45 and 46: 2.8.4 Redundant PSU and Power backp
Page 47 and 48: Install the PSU and Power backplane
Page 49 and 50: 2.8.5 SAS/SATA2 Backpanel and Bridg
Page 51 and 52: 2. Push the SAS/SATA2 Backplane as
Page 53 and 54: 5. Lift the front side of the top c
Page 55 and 56: ® ® DSBF-DR1 2.8.7 Motherboard Re
Page 57 and 58: CHAPTER 3 Installation Options
Page 59 and 60: 3.3 Attaching the rails to the rack
Page 61 and 62: CHAPTER 4 Motherboard Information
Page 63 and 64: Layout contents Slots/Sockets Page
Page 65 and 66: ® ® 2. USB device wake-up (3-pin
Page 67 and 68: ® ® 6. SAS controller setting (3-
Page 69 and 70: CHAPTER 5 BIOS Setup
Page 71 and 72: 5.1.2 Updating the BIOS using the P
Page 73 and 74: 5.2.1 BIOS menu screen Menu items M
Page 75 and 76: 5.2.7 Pop-up window Select a menu i
Page 77 and 78: 5.3.4 IDE Configuration Main Phoeni
Page 79 and 80: 5.3.5 IDE Channel 0 Master/Slave SA
Page 81 and 82: Processor Displays the CPU inforamt
Page 83 and 84: Multiprocessor Specification [1.4]
Page 85 and 86: Patrol Scrub Enable [Enabled] Allow
Page 87 and 88: 5.4.4 ICH USB Control Sub-Menu The
Page 89 and 90: Mode [Normal] Allows you to set the
Page 91 and 92:
Power On By RTC Alarm [Disabled] Al
Page 93 and 94:
Smart Fan Control [Smart Fan II] Al
Page 95 and 96:
The following items appear only if
Page 97 and 98:
5.6 Security menu PhoenixBIOS SETUP
Page 99 and 100:
5.7 Boot menu PhoenixBIOS SETUP UTI
Page 101 and 102:
POST Errors [Enabled] When set to E
Page 103 and 104:
CHAPTER 6 RAID Configuration
Page 105 and 106:
6.1.2 Installing hard disk drives T
Page 107 and 108:
3. The Adapter Properties screen ap
Page 109 and 110:
7. Repeat steps 5 and 6 to add the
Page 111 and 112:
By default, the RAID Disk field sho
Page 113 and 114:
4. The Select New Array Type screen
Page 115 and 116:
6.2.4 Managing Arrays The LSI Logic
Page 117 and 118:
Managing hot spares You may configu
Page 119 and 120:
Activating an array If an array is
Page 121 and 122:
Viewing SAS topology 1. From the Ad
Page 123 and 124:
6.2.6 Global_Properties From the Se
Page 125 and 126:
Restore Defaults This option allows
Page 127 and 128:
CHAPTER 7 Driver Installation
Page 129 and 130:
6. Place a blank, high-density flop
Page 131 and 132:
• Intel ® 6321ESB LSI Logic Embe
Page 133 and 134:
4. Right-click the RAID controller
Page 135 and 136:
5. When prompted, insert the Red Ha
Page 137 and 138:
4. When prompted, insert the RAID d
Page 139 and 140:
4. Click the Install Drivers option
Page 141 and 142:
8. Follow the screen instructions t
Page 143 and 144:
7.2.2 Red Hat/SuSE Linux Follow the
Page 145 and 146:
4. The ATI Software window appears.
Page 147 and 148:
APPENDIX A Reference Information
Page 149 and 150:
A.2.2 Using the EIST To use the EIS
Page 151 and 152:
A.4 Specifications Input Characteri
show all

Advantech HPC-1420-ISSE User Guide

Create successful ePaper yourself

Delete template?

Save as template?