Advantech HPC-1420-ISSE User Guide

More documents

Recommendations

Info

5. Using a screw driver to fasten the two screws on the power cable cover. 6. Put the device fan into its groove and connect the power cable. 7. Push the PSU into the chassis until a slight sound indicates it is properly seated in its place. 2-30 Chapter 2: Hardware Setup
2.8.5 SAS/SATA2 Backpanel and Bridge Card Follow the steps below to remove/install SAS/SATA2 Backplane and the Bridge Card. To remove the bridge card and and SAS/SATA Backplane: 1. Remove the top cover panel, then disconnect the 8-pin power cord to the SAS/SATA2 rear panel. 2. Disconnect the fan cables to the rear panel. 3. Using a screw driver to remove the screws on the cover of the bridge card. 4. Remove the cover panel to expose the bridge card that connects SAS/SATA2 rear panel and the system board. HPC-1420-ISSE User Manual 2-31
Page 1 and 2: HPC-1420-ISSE 1U DP Xeon HPC system
Page 3 and 4: 2.7 SAS/SATA backplane cabling.....
Page 5 and 6: 7.2.1 Windows 2000/Server 2003 ....
Page 7 and 8: Safety information Electrical Safet
Page 9 and 10: Conventions To make sure that you p
Page 11 and 12: CHAPTER 1 Product Introduction
Page 13 and 14: 1.2 System specifications The HPC-1
Page 15 and 16: 1.3 Front panel features The barebo
Page 17 and 18: 1.6 LED information 1.6.1 Front pan
Page 19 and 20: CHAPTER 2 Hardware Setup
Page 21 and 22: 5. Push the front side of the top c
Page 23 and 24: ® 2.2 Install the CPU and heatsink
Page 25 and 26: The CPU fits in only one correct or
Page 27 and 28: Rank population DIMM 32 DIMM 31 DIM
Page 29 and 30: 2.4 Hot-swap hard disk drives To in
Page 31 and 32: 2.5 Expansion slots 2.5.1 Installin
Page 33 and 34: 2.5.3 Remove the expansion cards To
Page 35 and 36: 2. Using a screw driver to secure t
Page 37 and 38: Standard interrupt assignments IRQ
Page 39 and 40: 2.6.1 Serial Port cable The system
Page 41 and 42: 2.8 Remove components Before instal
Page 43 and 44: 2.8.2 Device fans The system comes
Page 45 and 46: 2.8.4 Redundant PSU and Power backp
Page 47: Install the PSU and Power backplane
Page 51 and 52: 2. Push the SAS/SATA2 Backplane as
Page 53 and 54: 5. Lift the front side of the top c
Page 55 and 56: ® ® DSBF-DR1 2.8.7 Motherboard Re
Page 57 and 58: CHAPTER 3 Installation Options
Page 59 and 60: 3.3 Attaching the rails to the rack
Page 61 and 62: CHAPTER 4 Motherboard Information
Page 63 and 64: Layout contents Slots/Sockets Page
Page 65 and 66: ® ® 2. USB device wake-up (3-pin
Page 67 and 68: ® ® 6. SAS controller setting (3-
Page 69 and 70: CHAPTER 5 BIOS Setup
Page 71 and 72: 5.1.2 Updating the BIOS using the P
Page 73 and 74: 5.2.1 BIOS menu screen Menu items M
Page 75 and 76: 5.2.7 Pop-up window Select a menu i
Page 77 and 78: 5.3.4 IDE Configuration Main Phoeni
Page 79 and 80: 5.3.5 IDE Channel 0 Master/Slave SA
Page 81 and 82: Processor Displays the CPU inforamt
Page 83 and 84: Multiprocessor Specification [1.4]
Page 85 and 86: Patrol Scrub Enable [Enabled] Allow
Page 87 and 88: 5.4.4 ICH USB Control Sub-Menu The
Page 89 and 90: Mode [Normal] Allows you to set the
Page 91 and 92: Power On By RTC Alarm [Disabled] Al
Page 93 and 94: Smart Fan Control [Smart Fan II] Al
Page 95 and 96: The following items appear only if
Page 97 and 98: 5.6 Security menu PhoenixBIOS SETUP
Page 99 and 100:
5.7 Boot menu PhoenixBIOS SETUP UTI
Page 101 and 102:
POST Errors [Enabled] When set to E
Page 103 and 104:
CHAPTER 6 RAID Configuration
Page 105 and 106:
6.1.2 Installing hard disk drives T
Page 107 and 108:
3. The Adapter Properties screen ap
Page 109 and 110:
7. Repeat steps 5 and 6 to add the
Page 111 and 112:
By default, the RAID Disk field sho
Page 113 and 114:
4. The Select New Array Type screen
Page 115 and 116:
6.2.4 Managing Arrays The LSI Logic
Page 117 and 118:
Managing hot spares You may configu
Page 119 and 120:
Activating an array If an array is
Page 121 and 122:
Viewing SAS topology 1. From the Ad
Page 123 and 124:
6.2.6 Global_Properties From the Se
Page 125 and 126:
Restore Defaults This option allows
Page 127 and 128:
CHAPTER 7 Driver Installation
Page 129 and 130:
6. Place a blank, high-density flop
Page 131 and 132:
• Intel ® 6321ESB LSI Logic Embe
Page 133 and 134:
4. Right-click the RAID controller
Page 135 and 136:
5. When prompted, insert the Red Ha
Page 137 and 138:
4. When prompted, insert the RAID d
Page 139 and 140:
4. Click the Install Drivers option
Page 141 and 142:
8. Follow the screen instructions t
Page 143 and 144:
7.2.2 Red Hat/SuSE Linux Follow the
Page 145 and 146:
4. The ATI Software window appears.
Page 147 and 148:
APPENDIX A Reference Information
Page 149 and 150:
A.2.2 Using the EIST To use the EIS
Page 151 and 152:
A.4 Specifications Input Characteri
show all

Advantech HPC-1420-ISSE User Guide

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?