Shanks Owners manual (10 Build) 30, 30H, 35, 35H, 40 ... - EP Barrus

More documents

Recommendations

Info

3. To replace a Gauge illumination bulb. a. Unscrew and pull out the instrument panel. b. The illumination bulb holder is a push fit in the rear of the gauge. c. The cap less bulb is a push fit in the holder. 4. To replace a Gauge warning light bulb. a. Unscrew and pull out the instrument panel. b. The warning light bulb holder is a push fit in the rear of the gauge, but is retained by a plastic clip. Gently push the clip to one side to release the holder. c. The cap less bulb is a push fit in the holder. d. Ensure that on refitting, the bulb holder is retained by the clip, you should confirm correct positioning when the clip “clicks” when locked. 5. To replace a warning light bulb. • The warning light bulbs are accessible from the front of the panel. • Carefully prise out the coloured lens • With needle nose pliers, remove the clear lens to reveal the bulb The cap less bulb is a push fit in the holder 14. Checking Injection Pump Oil CAUTION: REMOVE THE IGNITION KEY BEFORE WORKING IN THE ENGINE COMPARTMENT. • Check oil level on small yellow dipstick adjacent to fuel injection pump. • Top up as necessary using engine oil from a small oil can. Lift pump plunger Dipstick Figure 11: Fuel Injection Pump Drain screw RDG6039484 Shanks10 Owners Manual Issue 1 Page 30 of 51
15. Gearbox Hydraulic Oil Filter (Shanks 30H, 35H, 40 and 45) CAUTION: REMOVE THE IGNITION KEY BEFORE WORKING IN THE ENGINE COMPARTMENT. • Check gearbox oil weekly and at recommended service period remove filter and clean. • Drain gearbox oil; oil capacity of the MA125A gearbox is 4.8L and 2L for the MA100. • The procedure is the same for both; remove the banjo bolt going into the filter and ease the adjacent banjo bolt (as shown below to allow access to the filter). • Remove bolt filter; clean and replace, ensuring all sealing washers are in good condition. Replace any which are damaged. • Refill gearbox with correct amount of 15W40 CD grade oil. • Take care not to overfill gearbox as damage may occur to internal components. • Start and run engine for a short period. • Check filter head to ensure there are no leaks. Hydraulic gearbox filter Banjo bolts RDG6039484 Shanks10 Owners Manual Issue 1 Page 31 of 51
Page 1 and 2: SHANKS CANAL BOAT ENGINE MANUAL For
Page 3 and 4: 5. Primary Fuel Filter Change .....
Page 5 and 6: PLEASE NOTE: This manual has been c
Page 7 and 8: 6. Batteries WARNING: EXPLOSIVE GAS
Page 9 and 10: SECTION 3 - Installation 1. Ventila
Page 11 and 12: engine, along with the 10mm packing
Page 13 and 14: 9. Engine Alignment • The gearbox
Page 15 and 16: pump lift pump (see Figure 11 page
Page 17 and 18: 14. Calorifier • The temperature
Page 19 and 20: • Visually check the engine for o
Page 21 and 22: Filler Cap Air Vent to Header Tank.
Page 23 and 24: element simply pulls out. • The a
Page 25 and 26: 4. Primary Fuel Filter Water Drain
Page 27 and 28: • Clean up any spilt fuel and dry
Page 29: hand, to guide the new belt into th
Page 33 and 34: when observed from the front of the
Page 35 and 36: SECTION 6 - Service Schedule Specif
Page 37 and 38: SECTION 7 - Shanks Engine Specifica
Page 39 and 40: SECTION 8 - Wiring Diagrams Harness
Page 41 and 42: Panel Wiring Diagram RDG6039484 Sha
Page 43 and 44: SECTION 9 - General Arrangements Sh
Page 45 and 46: Shanks10 35 RDG6039484 Shanks10 Own
Page 47 and 48: Shanks10 40 RDG6039484 Shanks10 Own
Page 49 and 50: Shanks Instrument Panels Engine ove
Page 51: SECTION 11 - Shanks Service Parts E

Shanks Owners manual (10 Build) 30, 30H, 35, 35H, 40 ... - EP Barrus

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?