USER'S GUIDE - Ono

More documents

Recommendations

Info

34 HITRON CDE-30364 USER’S <strong>GUIDE</strong> FIGURE 8: The Cable > Status Screen The following table describes the labels in this screen. TABLE 8: The Cable > Status Screen CM Configuration File This displays the name of the configuration file that the Name CDE-30364 downloaded from your service provider. This file provides the CDE-30364 with the service parameter data that it needs to perform its functions correctly. Network Access This displays whether or not your service provider allows you to access the Internet over the CATV connection. Downstream Permitted displays if you can access the Internet. Denied displays if you cannot access the Internet. NOTE: The downstream signal is the signal transmitted to the CDE-30364. CABLE
HITRON CDE-30364 USER’S <strong>GUIDE</strong> 35 TABLE 8: The Cable > Status Screen (continued) Frequency to Tune to This displays the current center frequency in Hertz (Hz) over which data is transmitted to the CDE-30364 over the CATV interface. This is the frequency to which the CDE-30364 is locked in; it will only scan for another frequency if this frequency becomes unavailable. If you want the CDE-30364 to attempt to connect at a different frequency, enter it in the field and click Apply. Scanning Start Frequency Channel Frequency Modulation Signal Strength Signal Noise Ratio Upstream NOTE: Do not change the frequency unless you have a good reason to do so. This displays the frequency in Hertz (Hz) at which the CDE-30364 begins scanning for a connection over the CATV interface (if a frequency is not already locked in). This displays the actual frequency of each downstream data channel to which the CDE-30364 is connected. This displays the type of modulation that each downstream channel uses. Possible modulation types This displays the power of the signal of each downstream data channel to which the CDE-30364 is connected, in dBmV (decibels above/below 1 millivolt). This displays the Signal to Noise Ratio (SNR) of each downstream data channel to which the CDE-30364 is connected, in dB (decibels). NOTE: The upstream signal is the signal transmitted from the CDE-30364. Channel ID Upstream Frequency Upstream Bandwidth SCDMA Mode Transmission Signal Strength Cable Modem IP Information IP Address Subnet Mask This displays the ID number of each channel on which the upstream signal is transmitted. This displays the frequency in Herz (Hz) of each upstream data channel to which the CDE-30364 is connected. This displays the bandwidth of each upstream data channel to which the CDE-30364 is connected (in Hertz). This displays the Synchronous Code Division Multiple Access (SCDMA) mode of each channel on which the upstream signal is transmitted. This displays the transmitted power of the signal of each upstream data channel to which the CDE-30364 is connected, in dBmV (decibels above/below 1 millivolt). This displays the CDE-30364’s WAN IP address. This IP address is automatically assigned to the CDE-30364 This displays the CDE-30364’s WAN subnet mask. CABLE
Page 1: USER’S GUIDE Hitron CDE-30364 VER
Page 4 and 5: HITRON CDE-30364 USER’S GUIDE 4 B
Page 6 and 7: 6 HITRON CDE-30364 USER’S GUIDE A
Page 8 and 9: 8 HITRON CDE-30364 USER’S GUIDE 2
Page 10 and 11: 10 HITRON CDE-30364 USER’S GUIDE
Page 84 and 85:
84 HITRON CDE-30364 USER’S GUIDE
Page 86 and 87:
Page 88 and 89:
Page 90 and 91:
Page 92 and 93:
Page 94 and 95:
Page 96 and 97:
Page 98 and 99:
Page 100 and 101:
Page 102 and 103:
Page 104 and 105:
Page 106 and 107:
Page 108 and 109:
Page 110 and 111:
Page 112:
show all

USER'S GUIDE - Ono

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?