USER'S GUIDE - Ono

More documents

Recommendations

Info

42 HITRON CDE-30364 USER’S <strong>GUIDE</strong> TABLE 11: The LAN > LAN IP Screen (continued) Domain Suffix Use this field to define the domain that you can enter into a Web browser (instead of an IP address) to reach the CDE- 30364 on the LAN. Private LAN DHCP Setting Enable LAN DHCP Lease Time DHCP Start IP DHCP End IP NOTE: The Domain Suffix is hitronhub.home by default. Select this if you want the CDE-30364 to provide IP addresses to network devices on the LAN automatically. Deselect this if you already have a DHCP server on your LAN, or if you wish to assign IP addresses to your computers and other network devices manually. Use this field to define the time after which the CDE-30364 renews the IP addresses of all the network devices connected to the CDE-30364 on the LAN (when DHCP is enabled). Use this field to specify the IP address at which the CDE- 30364 begins assigning IP addresses to devices on the LAN (when DHCP is enabled). Use this field to specify the IP address at which the CDE- 30364 stops assigning IP addresses to devices on the LAN (when DHCP is enabled). Host Name IP Address MAC Address Type Interface Apply Cancel Help NOTE: Devices requesting IP addresses once the DHCP pool is exhausted are not assigned an IP address. This displays the name of each network device connected on the LAN. This displays the IP address of each network device connected on the LAN. This displays the Media Access Control (MAC) address of each network device connected on the LAN. This displays whether the device’s IP address was assigned by DHCP (DHCP-IP), or self-assigned. This displays whether the device is connected on the LAN (Ethernet) or the WLAN (Wireless(x), where x denotes the wireless mode; b, g or n). Click this to save your changes to the fields in this screen. Click this to return the fields in this screen to their lastsaved values without saving your changes. Click this to see information about the fields in this screen. 3.3 THE SWITCH SETUP SCREEN Use this screen to see information about the data rate and flow of each of the CDE- 30364’s LAN ports, and to activate or deactivate each port. LAN
HITRON CDE-30364 USER’S <strong>GUIDE</strong> 43 Click LAN > Switch Setup. The following screen displays. FIGURE 12: The LAN > Switch Setup Screen The following table describes the labels in this screen. TABLE 12: The LAN > Switch Setup Screen Port This displays the LAN port number. Speed Duplex Active Apply Cancel Help This displays the maximum achievable data speed in megabits per second (MBPS). This displays Full when data can flow inbetween the CDE-30364 and the connected device in both directions simultaneously. This displays Half when data can flow inbetween the CDE-30364 and the connected device in only one direction at a time. Select a Port’s checkbox to enable communications between the CDE-30364 and devices connected to the port. Deselect a Port’s checkbox if you do not want to exchange data between the CDE-30364 and devices connected to the port. Click this to save your changes to the fields in this screen. Click this to return the fields in this screen to their lastsaved values without saving your changes. Click this to see information about the fields in this screen. 3.4 THE DEBUG SCREEN Use this screen to perform ping and traceroute tests on IP addresses or URLs. Click LAN > Debug. The following screen displays. LAN
Page 1: USER’S GUIDE Hitron CDE-30364 VER
Page 4 and 5: HITRON CDE-30364 USER’S GUIDE 4 B
Page 6 and 7: 6 HITRON CDE-30364 USER’S GUIDE A
Page 8 and 9: 8 HITRON CDE-30364 USER’S GUIDE 2
Page 10 and 11: 10 HITRON CDE-30364 USER’S GUIDE
Page 92 and 93:
92 HITRON CDE-30364 USER’S GUIDE
Page 94 and 95:
Page 96 and 97:
Page 98 and 99:
Page 100 and 101:
Page 102 and 103:
Page 104 and 105:
Page 106 and 107:
Page 108 and 109:
Page 110 and 111:
Page 112:
show all

USER'S GUIDE - Ono

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?