M68000 Microprocessor User's Manual

More documents

Recommendations

Info

BIT DATA 1 BYTE = 8 BITS 7 6 5 4 3 2 1 0 INTEGER DATA 1 BYTE = 8 BITS 7 6 5 4 3 2 1 0 BYTE 0 LOWER ADDRESSES BYTE 1 BYTE 2 BYTE 3 HIGHER ADDRESSES 1 WORD = 2 BYTES = 16 BITS BYTE 0 BYTE 1 (MS BYTE) (LS BYTE) WORD 0 LOWER ADDRESSES BYTE 0 (MS BYTE) BYTE 1 (LS BYTE) WORD 1 HIGHER ADDRESSES 1 LONG WORD = 2 WORDS = 4 BYTES = 32 BITS BYTE 0 BYTE 1 BYTE 2 BYTE 3 LONG WORD 0 HIGH-ORDER WORD LOW-ORDER WORD LOWER ADDRESSES BYTE 0 BYTE 1 BYTE 2 BYTE 3 LONG WORD 1 HIGH-ORDER WORD LOW-ORDER WORD HIGHER ADDRESSES Figure 2-7. Memory Data Organization of the MC68008 2.5 INSTRUCTION SET SUMMARY Table 2-2 provides an alphabetized listing of the M68000 instruction set listed by opcode, operation, and syntax. In the syntax descriptions, the left operand is the source operand, and the right operand is the destination operand. The following list contains the notations used in Table 2-2. 2-8 M68000 8-/16-/32-BIT MICROPROCESSOR USER’S MANUAL MOTOROLA
Notation for operands: PC — Program counter SR — Status register V — Overflow condition code Immediate Data — Immediate data from the instruction Source — Source contents Destination — Destination contents Vector — Location of exception vector +inf — Positive infinity –inf — Negative infinity — Operand data format: byte (B), word (W), long (L), single (S), double (D), extended (X), or packed (P). FPm — One of eight floating-point data registers (always specifies the source register) FPn — One of eight floating-point data registers (always specifies the destination register) Notation for subfields and qualifiers: of — Selects a single bit of the operand {offset:width} — Selects a bit field () — The contents of the referenced location 10 — The operand is binary-coded decimal, operations are performed in decimal () — The register indirect operator –() — Indicates that the operand register points to the memory ()+ — Location of the instruction operand—the optional mode qualifiers are –, +, (d), and (d, ix) #xxx or # — Immediate data that follows the instruction word(s) Notations for operations that have two operands, written , where is one of the following: → — The source operand is moved to the destination operand ↔ — The two operands are exchanged + — The operands are added – — The destination operand is subtracted from the source operand × — The operands are multiplied ÷ — The source operand is divided by the destination operand < — Relational test, true if source operand is less than destination operand > — Relational test, true if source operand is greater than destination operand V — Logical OR ⊕ — Logical exclusive OR Λ — Logical AND MOTOROLA M68000 8-/16-/32-BIT MICROPROCESSOR USER’S MANUAL 2-9
Page 1 and 2: µ MOTOROLA M68000 8-/16-/32-Bit Mi
Page 3 and 4: TABLE OF CONTENTS (Continued) Parag
Page 5 and 6: TABLE OF CONTENTS (Continued) Parag
Page 7 and 8: LIST OF ILLUSTRATIONS Figure Page N
Page 9 and 10: LIST OF ILLUSTRATIONS (Concluded) F
Page 11 and 12: LIST OF TABLES (Concluded) Table Pa
Page 13 and 14: 1.1 MC68000 The MC68000 is the firs
Page 15 and 16: SECTION 2 INTRODUCTION The section
Page 17 and 18: tables. The SFC and DFC registers a
Page 19 and 20: Register Direct Addressing Data Reg
Page 21: BIT DATA 1 BYTE = 8 BITS 7 6 5 4 3
Page 25 and 26: Table 2-2. Instruction Set Summary
Page 27 and 28: Table 2-2. Instruction Set Summary
Page 29 and 30: SECTION 3 SIGNAL DESCRIPTION This s
Page 31 and 32: V CC (2) GND(2) CLK ADDRESS BUS DAT
Page 33 and 34: Table 3-1. Data Strobe Control of D
Page 35 and 36: 3.6 SYSTEM CONTROL The system contr
Page 37 and 38: Table 3-3. Function Code Outputs Fu
Page 39 and 40: SECTION 4 8-BIT BUS OPERATION The f
Page 41 and 42: A bus cycle consists of eight state
Page 43 and 44: The descriptions of the eight state
Page 45 and 46: CLK S0 S1 S2 S3 S4 S5 S6 S7 S8 S9 S
Page 47 and 48: SECTION 5 16-BIT BUS OPERATION The
Page 49 and 50: CLK S0 S1 S2 S3 S4 S5 S6 S7 S0 S1 S
Page 51 and 52: The word and byte write-cycle timin
Page 53 and 54: STATE 7 On the falling edge of the
Page 55 and 56: STATE 12 STATE 13 STATE 14 STATE 15
Page 57 and 58: The breakpoint acknowledge cycle is
Page 59 and 60: PROCESSOR REQUESTING DEVICE REQUEST
Page 61 and 62: us request signal. When no acknowle
Page 63 and 64: RA 1 RA GT 1 XA RA GT RA GT RA XX R
Page 65 and 66: BUS RELEASED FROM THREE STATE AND P
Page 67 and 68: BUS THREE-STATED BG ASSERTED BR VAL
Page 69 and 70: BUS THREE-STATED BG ASSERTED BR VAL
Page 71 and 72: CLK S0 S2 S4 S6 FC2-FC0 A23-A1 AS U
Page 73 and 74:
CLK S0 S2 S4 S6 S0 S2 S4 S6 FC2-FC0
Page 75 and 76:
A double bus fault occurs during a
Page 77 and 78:
Case No. Control Signal 1 DTACK BER
Page 79 and 80:
ADDR AS R/W UDS/LDS DATA DTACK Figu
Page 81 and 82:
ADDR 11 AS 20A R/W 22 UDS/LDS 55 26
Page 83 and 84:
On the rising edge of the clock, at
Page 85 and 86:
Parameter #47 of Section 10 Electri
Page 87 and 88:
The privilege mode is a mechanism f
Page 89 and 90:
6.2 EXCEPTION PROCESSING The proces
Page 91 and 92:
equests from peripheral devices for
Page 93 and 94:
6.2.3 Multiple Exceptions These par
Page 95 and 96:
SSP EVEN BYTE ODD BYTE 7 0 7 0 15 0
Page 97 and 98:
interrupt priority mask is set at l
Page 99 and 100:
A signed divide (DIVS) or unsigned
Page 101 and 102:
After the execution of the instruct
Page 103 and 104:
. 15 14 13 12 11 10 9 8 7 6 5 4 3 2
Page 105 and 106:
6.4 RETURN FROM EXCEPTION (MC68010)
Page 107 and 108:
Table 7-1. Effective Address Calcul
Page 109 and 110:
In Table 7-5, the following notatio
Page 111 and 112:
CLR Table 7-7. Single Operand Instr
Page 113 and 114:
7.9 JMP, JSR, LEA, PEA, AND MOVEM I
Page 115 and 116:
Table 7-13. Miscellaneous Instructi
Page 117 and 118:
SECTION 8 16-BIT INSTRUCTION EXECUT
Page 119 and 120:
Table 8-3. Move Long Instruction Ex
Page 121 and 122:
Table 8-5. Immediate Instruction Ex
Page 123 and 124:
8.7 BIT MANIPULATION INSTRUCTION EX
Page 125 and 126:
Table 8-11. Multiprecision Instruct
Page 127 and 128:
the handler routine. The total numb
Page 129 and 130:
9.1 OPERAND EFFECTIVE ADDRESS CALCU
Page 131 and 132:
Table 9-4. Move Long Instruction Ex
Page 133 and 134:
9.4 IMMEDIATE INSTRUCTION EXECUTION
Page 135 and 136:
Table 9-11. Single Operand Instruct
Page 137 and 138:
Table 9-15. Conditional Instruction
Page 139 and 140:
Table 9-18. Miscellaneous Instructi
Page 141 and 142:
SECTION 10 ELECTRICAL AND THERMAL C
Page 143 and 144:
Table 10-1 summarizes maximum power
Page 145 and 146:
is lost through the active P-channe
Page 147 and 148:
10.6 MC68000/68008/68010 DC ELECTRI
Page 149 and 150:
. 10.9 MC68008 AC ELECTRICAL SPECIF
Page 151 and 152:
Num Characteristic 8 MHz* 10 MHz* 1
Page 153 and 154:
S0 S1 S2 S3 S4 S5 S6 S7 CLK 6A FC2-
Page 155 and 156:
10.11 AC ELECTRICAL SPECIFICATIONS
Page 157 and 158:
10.12 AC ELECTRICAL SPECIFICATIONS
Page 159 and 160:
CLK 47 33 BR BG 1 BGACK 35 47 34 37
Page 161 and 162:
CLK 47 33 BR BG 1 BGACK 35 47 34 37
Page 163 and 164:
10.13 MC68EC000 DC ELECTRICAL SPECI
Page 165 and 166:
Num Characteristic 8 MHz 10 MHz 12.
Page 167 and 168:
S0 S1 S2 S3 S4 S5 S6 S7 CLK 6A FC2-
Page 169 and 170:
CLK 47 33 BR 34 35 36 BG 39 38 58 A
Page 171 and 172:
11-2 M68000 8-/16-/32-BIT MICROPROC
Page 173 and 174:
R/W LDS UDS AS D0 D1 D2 D3 D4 D5 D6
Page 175 and 176:
A3 1 48 A2 A4 2 47 A1 A5 3 46 A0 A6
Page 177 and 178:
64 33 L SUFFIX 746-03 B 1 32 A F C
Page 179 and 180:
64 33 L SUFFIX 746-01 B 1 32 A F C
Page 181 and 182:
Figure 11-11. Case 765A-05—RC Suf
Page 183 and 184:
1. Fetch the MOVE instruction. 2. F
show all

M68000 Microprocessor User's Manual

Create successful ePaper yourself

Delete template?

Save as template?