VW 150-5 Workshop Manual - Zanshin

More documents

Recommendations

Info

Notes: The display fields in the functions 04 - Basic setting and 08 - Reading measurement value block, are shown from top to bottom. The following test procedures are described for the fault output device V.A.G 1552. 01-9
Fault memory Interrogate fault memory Special tools, workshop equipment, test and measuring equipment and accessories required V.A.G 1552 ♦ Fault output device V.A.G 1552 with cable V.A.G 1551/3 or fault output device VAS 5052 Procedure W00--1188 - Connect the fault output device V.A.G 1552 (VAS 5052) and select the engine electronics control unit with the ”Address word” 01. Here, the engine should be idling. (Connecting fault output device and selecting engine control unit ⇒ page 01-4) Only if the engine does not start: Rapid data transfer Select function XX X faults detected! HELP - Switch on the ignition. Display: - Keep an eye on the information that appears on the display while operating the vehicle system tester: - Press the keys 0 and 2 for the function ”Query fault memory” and confirm the input using the Q key. The display shows the number of faults stored or ”No faults detected!”. 01-10
Page 1 and 2: Service. Workshop Manual VW Marine
Page 3 and 4: 10 Removing and installing engine P
Page 5 and 6: 20 Fuel supply system Page Parts of
Page 7 and 8: 27 Starter, Current supply Page Sta
Page 9 and 10: Safety Precautions and Technical Da
Page 11 and 12: Open the cap of the cooling system
Page 13 and 14: Technical Data Engine number The en
Page 15 and 16: Code letters BCU ANG BCV ANH Manufa
Page 17 and 18: Note: General information on self-d
Page 19 and 20: Connecting fault reader All functio
Page 21 and 22: Vehicle system test Enter address w
Page 23: Procedure VAS 5052 - Unscrew the co
Page 27 and 28: Erase fault memory Special tools, w
Page 29 and 30: Fault table Notes: ♦ The fault ta
Page 31 and 32: Output on V.A.G 1552/VAS 5052 16989
Page 49 and 50: Rapid data transfer Select function
Page 55 and 56: Evaluate measuring value blocks at
Page 57 and 58: Evaluation: Display of injection qu
Page 59 and 60: Evaluation: Display of accelerator
Page 61 and 62: Evaluation: Display of commencement
Page 63 and 64: Display group 007 with ignition on
Page 65 and 66: Display group 013 at idling (warm e
Page 67 and 68: Evaluation: Display of idle running
Page 69 and 70: Display group 19 with ignition on D
Page 71 and 72: Display group 125 at idle Display g
Page 73 and 74: Display group 000 (display values,
Page 75 and 76:
Evaluation: Display of commencement
Page 77 and 78:
Evaluation: Display of injection qu
Page 79 and 80:
Engine code letters ANG, BCU Displa
Page 81 and 82:
Display group 004 at full load (tes
Page 83 and 84:
Evaluation: Display of commencement
Page 85 and 86:
Engine code letters ANH, BCV Displa
Page 87 and 88:
Display group 010 at full load (tes
Page 89 and 90:
VW 313 3033 V.A.G 1332 VW 540 V.A.G
Page 91 and 92:
- Screw the central plug of the ins
Page 93 and 94:
- Unscrew the throttle linkage -1-
Page 95 and 96:
3033 - Hook in the lifting tackle 3
Page 97 and 98:
Engine with power steering pump - I
Page 99 and 100:
1 2 Gearbox bell for reversing gear
Page 101 and 102:
I III II IV Dismantling and assembl
Page 103 and 104:
1 2 3 4 5 6 7 8 9 10 Part I 1 - Dus
Page 105 and 106:
1 2 3 4 5 6 7 8 9 10 15 - Washer
Page 107 and 108:
1 2 3 4 5 6 7 8 9 4-Camshaftsprocke
Page 109 and 110:
1 2 3 4 5 6 Part III 26 25 24 23 7
Page 111 and 112:
26 25 24 23 1 2 3 4 5 6 7 8 9 10 11
Page 113 and 114:
1 2 3 4 5 6 23 - Cup packing ♦ Re
Page 115 and 116:
1 2 3 4 5 6 7 8 9 10 11 12 13 14 6
Page 117 and 118:
1 2 3 4 5 6 7 8 17 - 20 Nm ♦ M8,
Page 119 and 120:
Belt drive without power steering p
Page 121 and 122:
3 4 5 6 7 8 9 10 11 12 Removing and
Page 123 and 124:
3 4 5 6 7 8 9 10 11 12 16 - Cylinde
Page 125 and 126:
1 2 - Unscrew the bolts -arrows- fr
Page 127 and 128:
Removing - Remove toothed belt for
Page 129 and 130:
Fitting Note: The oil seal of the s
Page 131 and 132:
1 2 3 4 5 6 4-65Nm 2 1 2 3 4 5 6 7
Page 133 and 134:
Crankshaft dimensions (Dimensions i
Page 135 and 136:
11 2 1 2 3 4 3 - Piston ♦ Mark in
Page 137 and 138:
11 2 1 2 3 4 9 - Bearing shell ♦
Page 139 and 140:
Fig. 2 Checking piston-ring height
Page 141 and 142:
Fig. 4 Piston installation position
Page 143 and 144:
Test procedure VW382/7 VW385/17 Whe
Page 145 and 146:
31 30 29 28 27 26 25 24 23 22 1 2 3
Page 147 and 148:
31 30 29 28 27 1 2 3 4 5 6 7 6 - Dr
Page 149 and 150:
31 30 29 28 1 2 3 4 5 20 - Toothed
Page 151 and 152:
31 30 29 28 27 26 25 24 23 22 1 2 3
Page 153 and 154:
2065 A 2068 A Removing and installi
Page 155 and 156:
- Remove the tensioner for the ribb
Page 157 and 158:
A 2068 A Engine removed: - Set adju
Page 159 and 160:
- Centre adjustment ruler as follow
Page 161 and 162:
However, if it is accidentally turn
Page 163 and 164:
- Toothed belt for injection pump
Page 165 and 166:
Preconditions The engine may be a m
Page 167 and 168:
9 5 3 1 7 11 - Tighten cylinder hea
Page 169 and 170:
Test condition Engine oil temperatu
Page 171 and 172:
19 1 2 1 3 4 5 6 7 8 9 10 11 12 13
Page 173 and 174:
1 2 1 3 8 - Valve stem seal ♦ Ren
Page 175 and 176:
VW 387 Fig. 1 Checking camshaft, ax
Page 177 and 178:
Fig. 4 Camshaft marking, valve timi
Page 179 and 180:
- Measure distance -a- between valv
Page 181 and 182:
VW387 Test procedure - Insert new v
Page 183 and 184:
2036 10 -204 3047 A VW 541/1A Renew
Page 185 and 186:
A B 10 - 204 Fitting - To prevent d
Page 187 and 188:
Checking hydraulic bucket tappets S
Page 189 and 190:
Removing and installing parts of lu
Page 191 and 192:
1 2 3 4 5 6 7 8 9 10 11 10 Part I 1
Page 193 and 194:
1 2 3 4 5 6 7 8 9 10 11 10 8-Camsha
Page 195 and 196:
1 2 3 4 5 6 7 8 9 10 18 11 12 13 14
Page 197 and 198:
1 2 3 4 5 6 7 8 9 10 18 11 12 13 14
Page 199 and 200:
32 31 30 1 2 3 10 - 10 Nm 11 - 20 N
Page 201 and 202:
32 31 30 1 2 3 24 - Hollow screw, 3
Page 203 and 204:
1 2 3 8 - Retaining clip 9-20Nm 28
Page 205 and 206:
1 2 3 25 - Oil return line 28 4 5 2
Page 207 and 208:
- Unscrew the oil sump. - If necess
Page 209 and 210:
Note: After fitting the oil sump, t
Page 211 and 212:
V.A.G 1342 Note: Operating test and
Page 213 and 214:
Removing and installing parts of co
Page 215 and 216:
29 28 1 2 3 4 5 6 7 8 9 Parts of co
Page 217 and 218:
1 2 3 14 - Connecting hose 29 28 4
Page 219 and 220:
1 2 3 28 - 20 Nm 29 28 4 5 6 7 8 9
Page 221 and 222:
Fig. 3 Installing housing-radiator
Page 223 and 224:
1 2 3 4 5 6 7 9 - Seawater filter h
Page 225 and 226:
1 2 3 4 5 - Connection piece 22 21
Page 227 and 228:
1 2 3 4 16 - Retaining clip ♦ che
Page 229 and 230:
1 2 3 4 5 7 - Locking ball 8 24 22
Page 231 and 232:
1 2 3 4 5 21 - 20 Nm 8 24 22 23 6 2
Page 233 and 234:
7 7 - Exhaust-pipe connection piece
Page 235 and 236:
7 6 8 11 - Oil cooler 12 - Coolant
Page 237 and 238:
7 6 8 10 - Cylinder block 11 - Oil
Page 239 and 240:
Draining - Open cap of housing-radi
Page 241 and 242:
Recommended mixing ratio: Antifreez
Page 243 and 244:
Removing Notes: ♦ Always renew ga
Page 245 and 246:
1 2 Fitting Installation is carried
Page 247 and 248:
1 2 - Lever the rubber protection c
Page 249 and 250:
Parts of fuel supply Dismantling an
Page 251 and 252:
33 32 31 30 29 28 27 26 24 23 22 20
Page 253 and 254:
33 32 31 30 29 28 27 26 24 23 22 20
Page 255 and 256:
1 3 1 4 2 5 Servicing the Fuel Filt
Page 257 and 258:
Safety precautions when working on
Page 259 and 260:
1 10 9 2 1 3 4 Servicing throttle c
Page 261 and 262:
V.A.G 1526 A V.A.G 1552 V.A.G 1594
Page 263 and 264:
Read measuring value block 2 → rp
Page 265 and 266:
- Separate the 6-pin connector for
Page 267 and 268:
Adjusting accelerator lever positio
Page 269 and 270:
1 - Tighten the mounting screws -ar
Page 271 and 272:
33 1 2 3 4 3 5 6 1 - To intake mani
Page 273 and 274:
33 1 2 3 4 3 5 6 7 21 - Gasket ♦
Page 275 and 276:
1 2 3 4 5 6 Removing and installing
Page 277 and 278:
1 2 3 4 5 6 13 - To housing-radiato
Page 279 and 280:
Removing and installing turbocharge
Page 281 and 282:
- Disconnect the air filter hose -a
Page 283 and 284:
- Unscrew the lower mounting bolts
Page 285 and 286:
- Position the oil supply line -arr
Page 287 and 288:
1 - Disconnect the connection hoses
Page 289 and 290:
Fitting Installation is carried out
Page 291 and 292:
Rapid data transfer Select function
Page 293 and 294:
Check the function of the pressure
Page 295 and 296:
Rules regarding cleanliness Always
Page 297 and 298:
1 2 3 4 5 6 7 8 SUPERIOR MARINE TEC
Page 299 and 300:
1 2 3 4 5 6 Fuse box/relay plate 1
Page 301 and 302:
1 2 3 4 5 6 13 - Glow plug relay (J
Page 303 and 304:
1 2 3 4 5 Removing and installing t
Page 305 and 306:
1 2 3 4 3 5 6 7 3 8 3 9 10 11 Servi
Page 307 and 308:
16 29 28 27 26 25 5 6 7 3 1 2 3 4 3
Page 309 and 310:
5 6 7 3 29 - 25 Nm 1 2 3 4 3 8 3 9
Page 311 and 312:
2068 A 3313 V.A.G 1332 3036 V.A.G 1
Page 313 and 314:
- Screw the TDC sender T 01901 into
Page 315 and 316:
- Place the toothed belt on the inj
Page 317 and 318:
Note: If the front pointer is outsi
Page 319 and 320:
3035 ♦ 3035 Ring spanner ♦ T 01
Page 321 and 322:
- Unscrew the securing screws -1- a
Page 323 and 324:
Blocking injection pump from delive
Page 325 and 326:
Notes: ♦ The dynamic test and cor
Page 327 and 328:
Note: ♦ During the check, if the
Page 329 and 330:
Defective nozzles can be detected b
Page 331 and 332:
Checking injection pressure Importa
Page 333 and 334:
- Install the fuse box/relay plate:
Page 335 and 336:
1 Test procedure - Open the cover -
Page 337 and 338:
- Check the cable connections to th
Page 339 and 340:
4 5 81 62 63 44 24 43 6 25 Check vo
Page 341 and 342:
Test procedure - Pull the plug off
Page 343 and 344:
V.A.G 1526 A V.A.G 1552 V.A.G 1594
Page 345 and 346:
Note: Depending on the weather, the
Page 347 and 348:
V.A.G 1526 A V.A.G 1552 V.A.G 1594
Page 349 and 350:
- If there is no realistic display
Page 351 and 352:
2 4 A - Check the wires between plu
Page 353 and 354:
Page 355 and 356:
7000 6000 5000 4000 3000 2000 A B 9
Page 357 and 358:
V.A.G 1526 A V.A.G 1552 V.A.G 1594
Page 359 and 360:
- Switch off the ignition. - Separa
Page 361 and 362:
1 3 5 7 9 A 2 4 6 8 10 1 2 98 105 1
Page 363 and 364:
V.A.G 1526 A V.A.G 1552 V.A.G 1594
Page 365 and 366:
Checking the Modulating Piston Move
Page 367 and 368:
- Separate the 10-pin connector for
Page 369 and 370:
Checking the Needle Lift Sender V.A
Page 371 and 372:
A 98 105 2 1 - Check the wires betw
Page 373 and 374:
Page 375 and 376:
10 8 6 4 2 - Measure resistance bet
Page 377 and 378:
V.A.G 1526 A V.A.G 1552 V.A.G 1594
Page 379 and 380:
- Press the → -button. - Press ke
Page 381 and 382:
Engine control unit Renewing engine
Page 383 and 384:
- Pull the relay -1- out of the soc
Page 385 and 386:
Test procedure - Remove the engine
Page 387 and 388:
1 2 3 4 Exhaust system without turb
Page 389 and 390:
1 2 3 6-40Nm ♦ Allen screw 7-Gask
Page 391 and 392:
Removing and installing starter V.A
Page 393 and 394:
- Unscrew the mounting screws -arro
Page 395 and 396:
A A Removing and installing voltage
Page 397 and 398:
3310 ♦ 3310 Socket head W00--0299
Page 399 and 400:
Alternator brackets and ribbed V-be
Page 401 and 402:
14 12 13 12 1 2 3 5 - Hexagon bolts
Page 403 and 404:
1 2 9 8 1 10 9 8 7 6 Y27--0005 Y27-
Page 405 and 406:
11 10 1 2 3 9 8 Y27--0008 4 5 6 7 F
Page 407 and 408:
Removing ribbed V-belt of alternato
Page 409 and 410:
Belt drive with alternator and addi
Page 411 and 412:
Additional 230 V alternator Importa
Page 413 and 414:
7 - Washers (8 mm x 25 mm) 1 2 3 4
Page 415 and 416:
Installing: Installation is carried
Page 417 and 418:
- Unscrew the two mounting screws -
Page 419 and 420:
The red LED lights up: ♦ Undervol
Page 421 and 422:
Test procedure - Remove the connect
Page 423 and 424:
Test procedure - Remove the engine
Page 425 and 426:
1 2 Function overview: Power steeri
Page 427 and 428:
1 2 Exploded view: Power steering p
Page 429 and 430:
1 2 11 - Seal ♦ Renew 12 - Screw
Page 431 and 432:
- Start engine and top up oil level
Page 433 and 434:
1 1 2 - Unscrew bolts -1- and -2-.
Page 435 and 436:
Removing and installing individual
Page 437 and 438:
Fuse box/relay plate Removing and i
Page 439 and 440:
- Unscrew the upper mounting screws
Page 441 and 442:
A B C D E F G N O M P L K J R H Y97
Page 443 and 444:
J H G F P N K v u t s r p n m a b c
Page 445 and 446:
J H G F E Z X W V f e d c b a s r p
Page 447 and 448:
Removing and installing earth switc
Page 449 and 450:
A B - Remove the support -A- togeth
Page 451 and 452:
Wiring loom between instrument pane
Page 453:
Repair instructions for wiring loom
show all

VW 150-5 Workshop Manual - Zanshin

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?