ETC Sensor 24x2-4K dimmer rack.pdf - Pacific Coast Entertainment

Recommendations

Info

CEM+ Playback Priorities The CEM+ uses the same priority structure as all of the ETC products that use ETCNet2 and adds two more internally. Any incoming EDMX is reprioritized internally on the CEM+ as set on the patch page. The priorities of the EDMX sources (Congo, Emphasis, Obsession II, Unison, ETCNet2 DMX Node) are used to determine what level information makes it to the CEM+. That level information is then flatly reprioritized to the level specified on the patch page. ETCNet2 EDMX Priorities Highest Priority Panic (CEM+) Any sources at the same Priority will pile-on (HTP) with each other. Lowest Priority Set Level (CEM+) Replace (Unison) Priority 1 Priority 20 Pass-Through If Active (Unison) That means that if (for the same set of EDMX addresses) you set your Emphasis to an EDMX priority of two (2), an Obsession II to a priority of nine (9) and an input port of a DMX Node to a priority of two (2), the level information will pile-on/HTP for the DMX Node and Emphasis and ignore the Obsession II’s levels. Internally to a CEM+ that EDMX level information will be prioritized and used at the EDMX priority setting on the patch page (defaults to a priority of 10). The EDMX priority is set on a rack-by-rack basis just like the DMX ports. Once inside the CEM+, the new priority is used when determining what source level information is used (EDMX, DMX Port A, DMX Port B, Presets, Set Levels and Panic). EDMX, DMX Port A, DMX Port B, and Presets can all be set with their own priorities (1-20). Set Levels and Panic have fixed priorities above the other priorities. See the inset above. 6 Sensor+ CEM+ Configuration Manual
? ?? ? Chapter 2 Basic Navigation This manual covers functions and configuration of the CEM+ and Sensor+ Connect that are available to the User and Power User login levels of the full face panel menu. The Basic/Portable feature User Level Default/User Power User PIN None 3333 set and menu is covered in Appendix A: Basic/Portable Mode on page 53. The CEM+ User Interface You can access all the menus described in this chapter using the buttons on the face of the CEM+ module. Menus and messages are displayed on the integral 2x20 LCD display. Reset Plus Set Levels Home Back Minus Accept The CEM+ user interface: • Use to return to the main menu at any time. • Use and to scroll through menus and through digits and letters in screens requiring user input. • Use to accept settings and to view the error list. • Use to step back through menus. • Use to access the Set Levels menu. • Use to reset the CEM+. 2 Basic Navigation 7
Page 1: CEM+ Configuration Manual Version 2
Page 4 and 5: Chapter 4 CEM+ Procedures . . . . .
Page 6 and 7: iv Sensor+ CEM+ Configuration Manua
Page 8 and 9: What’s New in v2.0 Here’s a qui
Page 10 and 11: Sensor+ Connect Web Browser Interfa
Page 14 and 15: CEM+ Basic Operation The procedures
Page 16 and 17: Rack General The Rack General menu
Page 18 and 19: match all dimmed load. The default
Page 20 and 21: • Play Preset: this setting will
Page 22 and 23: do this by specifying: the rack vol
Page 24 and 25: Ambient Temp Type [Power] The Ambie
Page 26 and 27: Sensor+ Connect uses a navigation l
Page 28 and 29: Add Racks This page is where you ad
Page 30 and 31: Set Dimmer Name [User] The Set Name
Page 32 and 33: Errors Errors for a rack can be vie
Page 34 and 35: Room (1-4) Clicking on a room in th
Page 36 and 37: Patch The patch page provides a pow
Page 38 and 39: File Upload The File Upload web pag
Page 40 and 41: Browse into a CEM+ from Internet Ex
Page 42 and 43: Build New Configuration (from NoCon
Page 44 and 45: Set Dimmer Properties When a rack i
Page 46 and 47: Rooms & Presets Assign Dimmers to R
Page 48 and 49: Load Management Load management can
Page 50 and 51: Below is what the sensor.rak file l
Page 52 and 53: egin responding to incoming data. I
Page 54 and 55: Changing Installation Rack Modules
Page 56 and 57: CEM+ Fuses The CEM+ has two fuses:
Page 58 and 59: 52 Sensor+ CEM+ Configuration Manua
Page 60 and 61: if error SP48 D100AF Rack OK DMX St
Page 62 and 63:
Preset 1 Preset 2 Preset 3 Preset 4
Page 64 and 65:
OFF Station Options Control station
Page 66 and 67:
60 Sensor+ CEM+ Configuration Manua
Page 68 and 69:
Addressing In RTB systems, the cont
Page 70 and 71:
CEM+ Error Message Probable Cause P
Page 72 and 73:
Modified linear curve A modified li
Page 74 and 75:
68 Sensor+ CEM+ Configuration Manua
Page 76 and 77:
if Panic Active No if Error No Rack
Page 78 and 79:
Rack Menu Rack: xx/xx OK [Rack] Set
Page 80 and 81:
Rack: xx/xx OK [Group] Group Menu S
Page 82 and 83:
Appendix G Sensor+ Connect Site Map
Page 84:
Corporate Headquarters • 3031 Ple
show all

ETC Sensor 24x2-4K dimmer rack.pdf - Pacific Coast Entertainment

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?