ETC Sensor 24x2-4K dimmer rack.pdf - Pacific Coast Entertainment

Recommendations

Info

Add Racks This page is where you add racks to your configuration. Rack # Status First dimmer of the first added rack. Enable Advanced Features for added racks. 240V changes the available rack & module types to European models. (Read below) Set initial patch mode. Set ambient temperature alarm. Set the default module type Set the phase balancing type To change the rack and module types to the European models, click the 240V check box. After checking 240V, you must click Save Changes before you will see the available rack and module types change to European (ESR/ESP) models. Clicking Save Changes the first time after the 240V check box has been altered (checkmark vs. no checkmark) will not add a rack to the group. This page displays the individual rack’s power information, the dimmers’ control source and current intensity level. Displays which rack’s info you are viewing which may be different from the rack you logged in to. 22 Sensor+ CEM+ Configuration Manual
Configure Rack This page is the individual rack equivalent to the All Racks/Configure Rack page listed above. See “All Racks” on page 21. Configure Dimmers This webpage provides a single place to set all of your dimmer’s properties. Below is a list explaining each one of the settings. 3 Sensor+ Connect Web Interface Overview 23
Page 1: CEM+ Configuration Manual Version 2
Page 4 and 5: Chapter 4 CEM+ Procedures . . . . .
Page 6 and 7: iv Sensor+ CEM+ Configuration Manua
Page 8 and 9: What’s New in v2.0 Here’s a qui
Page 10 and 11: Sensor+ Connect Web Browser Interfa
Page 12 and 13: CEM+ Playback Priorities The CEM+ u
Page 14 and 15: CEM+ Basic Operation The procedures
Page 16 and 17: Rack General The Rack General menu
Page 18 and 19: match all dimmed load. The default
Page 20 and 21: • Play Preset: this setting will
Page 22 and 23: do this by specifying: the rack vol
Page 24 and 25: Ambient Temp Type [Power] The Ambie
Page 26 and 27: Sensor+ Connect uses a navigation l
Page 30 and 31: Set Dimmer Name [User] The Set Name
Page 32 and 33: Errors Errors for a rack can be vie
Page 34 and 35: Room (1-4) Clicking on a room in th
Page 36 and 37: Patch The patch page provides a pow
Page 38 and 39: File Upload The File Upload web pag
Page 40 and 41: Browse into a CEM+ from Internet Ex
Page 42 and 43: Build New Configuration (from NoCon
Page 44 and 45: Set Dimmer Properties When a rack i
Page 46 and 47: Rooms & Presets Assign Dimmers to R
Page 48 and 49: Load Management Load management can
Page 50 and 51: Below is what the sensor.rak file l
Page 52 and 53: egin responding to incoming data. I
Page 54 and 55: Changing Installation Rack Modules
Page 56 and 57: CEM+ Fuses The CEM+ has two fuses:
Page 58 and 59: 52 Sensor+ CEM+ Configuration Manua
Page 60 and 61: if error SP48 D100AF Rack OK DMX St
Page 62 and 63: Preset 1 Preset 2 Preset 3 Preset 4
Page 64 and 65: OFF Station Options Control station
Page 68 and 69: Addressing In RTB systems, the cont
Page 70 and 71: CEM+ Error Message Probable Cause P
Page 72 and 73: Modified linear curve A modified li
Page 76 and 77: if Panic Active No if Error No Rack
Page 78 and 79:
Rack Menu Rack: xx/xx OK [Rack] Set
Page 80 and 81:
Rack: xx/xx OK [Group] Group Menu S
Page 82 and 83:
Appendix G Sensor+ Connect Site Map
Page 84:
Corporate Headquarters • 3031 Ple
show all

ETC Sensor 24x2-4K dimmer rack.pdf - Pacific Coast Entertainment

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?