current_userManual - Audio Rents
current_userManual - Audio Rents
current_userManual - Audio Rents
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
AUDIO / VIDEO APPARATUS<br />
19NJ<br />
{<br />
To reduce the risk o fire<br />
replace only with same<br />
type and rating<br />
250V time-lag fuse.<br />
Installation and Maintenance<br />
Wiring Diagrams<br />
READER 1<br />
READER 2<br />
DIGITAL ACC.<br />
(Accessory I/O Only)<br />
MIC. INPUT<br />
RTA<br />
PA<br />
PA<br />
N/C<br />
ANALOG ACC. / MAG.<br />
OPTICAL 1<br />
R+<br />
L–<br />
R–<br />
L+<br />
OPTICAL 2<br />
Notes:<br />
1. Follow all local electrical and building codes.<br />
2. Use earthed (grounded) conduit wherever<br />
possible. Avoid routing signal wiring near electric<br />
motors, rectifiers, power wiring, dimmer wiring, or<br />
other sources of electrical noise.<br />
MODEL CP500<br />
CAUTION<br />
FUSE T 2A<br />
5mm x 20mm<br />
100 - 240 Vac 50 - 60 Hz 120 W<br />
6 CHANNEL INPUT<br />
(External Digital Processor)<br />
MUX PWR<br />
MUX GND<br />
MUX DATA<br />
1<br />
15-24V AC/DC IN<br />
2<br />
3<br />
4 DATA REMOTE<br />
5<br />
6 VREF<br />
FADER<br />
7 RTN<br />
8 N/C<br />
NONSYNC 1<br />
L R<br />
NONSYNC 2<br />
L R<br />
3. For two-conductor with shield wiring, use<br />
Belden 8451 two-conductor shielded cable or<br />
equivalent: tinned copper, twisted pair, 22AWG<br />
stranded tinned copper drain wire, aluminumpolyester<br />
shield, 100 percent shield coverage,<br />
conductor to conductor (111 pF per meter).<br />
From<br />
Automation<br />
4xAES Source<br />
Eight-Channel PCM<br />
from Server<br />
F91805A_3.CDR<br />
AUTOMATION<br />
SERIAL DATA<br />
Shielded<br />
Automation Cable F-M-F<br />
Dolby Part Number 83457<br />
Part of CDMA/D<br />
See Note 5.<br />
~<br />
100–240 Vac 50–60Hz 15W<br />
Dolby, Pro Logic and the double-D symbol<br />
are registered trademarks of Dolby Laboratories.<br />
MOTOR START<br />
TO CP CONTROL<br />
TO DA CONTROL<br />
Shielded<br />
4XAES Digital <strong>Audio</strong> Cable<br />
Dolby Part Number 8305580<br />
DSP100 TO DMA8PLUS<br />
BYPASS PWR / REMOTES<br />
1 2 5 6 7 8<br />
Shielded <strong>Audio</strong> Cable<br />
Dolby Part Number 83528<br />
Part of CDMA/D<br />
See Note 5.<br />
Digital Media<br />
Push Button<br />
or<br />
Relay Contacts<br />
(See Digital Media<br />
Automation<br />
Wiring Diagram)<br />
Digital Media Adapter<br />
DMA8Plus<br />
4xAES IN<br />
DIGITAL 1 IN<br />
This cable is included in the Cat. No. 899-DMA8<br />
Digital Cinema Installation Kit<br />
1xAES<br />
DIGITAL 2 IN<br />
L<br />
1xAES<br />
DIGITAL 3 IN<br />
R<br />
OPTICAL<br />
DIGITAL 4 IN<br />
Ls Rs SW<br />
HI<br />
DIGITAL MEDIA<br />
AUTOMATION<br />
RS-232<br />
Ms<br />
ACT<br />
X-OVER OUT<br />
HF<br />
BASS<br />
L R C Ls Rs<br />
10BASE-T<br />
{<br />
LINK<br />
AUDIO OUT TO CP<br />
ANALOG AUDIO IN<br />
Auditorium<br />
Network<br />
PCM<br />
Dolby Digital (AC-3)<br />
Dolby E<br />
4. All shields must be connected to the chassis of<br />
the CP500 or DMA8Plus rather than to circuit<br />
(audio) ground. This achieves the RF interference<br />
immunity required by the FCC and European EMC<br />
standards. For D-connectors, a metal housing<br />
must be used and the shields must be connected<br />
to the housing.<br />
5. The Shielded <strong>Audio</strong> and Automation Cables are<br />
included in the CDMA/D cable set.<br />
Digital 4<br />
Digital 3<br />
Digital 2<br />
Film<br />
Digital 1<br />
Push Button<br />
or<br />
Relay Contacts<br />
DIGITAL MEDIA<br />
AUTOMATION<br />
5<br />
8<br />
5<br />
4<br />
5<br />
3<br />
5<br />
2<br />
5<br />
1<br />
DIGITAL MEDIA AUTOMATION<br />
WIRING DIAGRAM<br />
5<br />
9<br />
6<br />
1<br />
DMA8PLUS TO CP500<br />
INSTALLATION WIRING<br />
Dolby ® DMA8Plus Digital Media Adapter Installation and User’s Manual 13
Change language