KES Touchscreen User Manual 2009 - Spring Air Systems Inc.

More documents

Recommendations

Info

Mo 09:00 01. 20. 03 LOGO! AUX! AP50C & AP50H three sequence electrical wiring Figure 49 _____________________________________________________________________________________________ Spring Air Systems Water Wash Ventilator Maintenance Manual 2010 Update 40
MAINTENANCE SCHEDULE DAILY: 1. After the manual or automatic wash wipe down the interior and exterior surfaces of the hood canopy and the underside of the grease trough. Use a damp cloth and avoid abrasive cleansers. WEEKLY: 1. Check the level of detergent in the control panel. (Panels with low detergent alarm will automatically signal when a refill is necessary). 2. During the normal fan operation visually inspect the cold-water spray nozzles. The nozzles can be observed by looking directly into the ventilator inlet slot. If a nozzle is not spraying remove/clean and or replace. (Type “C” extractors only.) 3. After the daily wash inspect the hot water wash manifold and nozzles. Open the front access door to view the wash manifold. If grease or dirt is still visible remove/clean and or replace the hot water nozzle. Prior to replacement check that hot water pressure and temperature are within design ranges. MONTHLY: 1. Check operation of detergent pump. Inspect for leaks and broken fittings. 2. After the daily wash inspect the complete interior of the grease extractor. Open the front access door and check the VORTEX BAFFLE and grease trough for any debris. Check that the drain is free and clear. SIX MONTHS: 1. Clean all line strainers located in the control panel (hot water and cold water). 2. Check exhaust fan belts for alignment, tightness, and wear. Adjust and/or replace. 3. Measure the exhaust volume. Design exhaust volume is stamped on the ULC plate. Refer to the Exhaust Air Measurement section of this manual for detailed instructions. 4. Check the Second Line Fire Protection System. 5. Hoods with makeup air only: remove filters from plenum and replace or wash in a mild detergent and water mix. Arrangement “T”: Manually activate system by placing a jumper across terminals 1 & 2 in the control panel. The following sequence should occur: (i) Fire damper closes. (ii) Exhaust fan shuts off. (iii) Hot water solenoid is energized spraying water into the interior of the grease extractor. Reset the fire damper by rotating the reset handle 90 degrees clockwise. (The handle is located on the side of the fire solenoid enclosure ENS.) Arrangement “F”: Visually inspect the fusible link, which holds the fire damper open. Clean and/or replace. Manually activate the Second Line Fire Protection System placing a jumper across terminals 1 & 2 in the control panel. The following sequence should occur: (i) (ii) Exhaust fan shuts off. Hot water solenoid is engaged spraying water into the interior of the grease extractor. CAUTION: PRIOR TO ACTIVATING THE HOOD AND DAMPER ASSEMBLY CHECK IF THE PRIMARY FIRE PROTECTION SYSTEM OR BUILDING FIRE ALARM IS ELECTRICALLY CONNECTED TO THE WATER WASH CONTROL PANEL. _____________________________________________________________________________________________ Spring Air Systems Water Wash Ventilator Maintenance Manual 2010 Update 41
Page 1 and 2: WATER WASH VENTILATOR MAINTENANCE M
Page 3 and 4: VENTILATOR OPERATING AND MAINTENANC
Page 5 and 6: An integral part of any SPRING AIR
Page 7 and 8: Typical Logo Processor Figure 5 Set
Page 9 and 10: Setting the length of the 1st wash
Page 11 and 12: MP20C Plumbing and Electrical Compo
Page 13 and 14: Setting the length of the 2nd wash
Page 15 and 16: REMOTE PIPING All remote piping mus
Page 17 and 18: AP20H, AP20C Mo 09:00 01. 20. 03 LO
Page 19 and 20: Setting Weekly Fan "ON" and "OFF" t
Page 21 and 22: GREASE EXTRACTOR OPERATION TYPE C G
Page 23 and 24: AUTOMATIC WASH TYPE C AND H: VENTIL
Page 25 and 26: HOT WATER REQUIRED MODEL S, B, & B-
Page 27 and 28: HOOD AND DAMPER ASSEMBLY THE SURFAC
Page 29 and 30: Dampers up over 32” long DAMPERS
Page 31 and 32: ALL MP & AP PANELS - ARRANGEMENT
Page 33 and 34: ARRANGMENT F: FUSIBLE LINK ACTIVATE
Page 35 and 36: BAFFLE SETTINGS Variflow Baffle lab
Page 37 and 38: MP20H two sequence hot water wash p
Page 39 and 40: Mo 09:00 01. 20. 03 LOGO! AP10C & A
Page 41: Mo 09:00 01. 20. 03 LOGO! AUX! AP30
Page 45 and 46: _____1. MEASURING THE SUPPLY AIRFLO
Page 47 and 48: MEASURING THE SUPPLY AIRFLOW - MJ T
Page 49 and 50: Poor Cleaning WASH + SYSTEM (I) Spr
Page 51 and 52: Su 00:00 01.01.00 Setting the Clock
Page 53 and 54: WATER WASH HOOD START-UP REPORT Gen
Page 55: Other Fine Products From • RevLow

KES Touchscreen User Manual 2009 - Spring Air Systems Inc.

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?