Knee Retractor - Innomed, Inc.

More documents

Recommendations

Info

Lower Extremity Leg Positioner Designed by Ronald Romanelli, MD Designed to lift the knee for lower extremity casting applications Supplied with one autoclavable silicone pad. Positioner is radiolucent and gas or steam sterilizable. PRODUCT NO’S: 2745 Dimensions: 5.5" H x 9.5" L x 9.25" W Replacement Parts: 2760-P [Silicone Pad] PROUDLY MADE IN THE USA Sanders Extremity Positioning Tubes Designed by Richard A. Sanders, MD Designed to support the knee and ankle during lower extremity surgery The 4" tube elevates the foot and ankle for ankle fracture surgery. The 6" tube lifts the knee off the operating table and allows for approximately 30° of knee fl exion. Very useful for closure of total knee incisions, supporting fractures of the distal femur, and tibia plateau fractures. The tubes are made of aluminum, allowing them to be autoclaved. They help eliminate the need for rolled sheet bolsters. PRODUCT NO’S: 2740-01 [Small] Diameter: 4" Width: 8" 2740-02 [Large] Diameter: 6" Width: 8" PROUDLY MADE IN THE USA Stulberg Sliding Bolster Designed by S. David Stulberg, MD Helps eliminate the need for a sand bag during total knee surgery The base plate is attached to the table and the sterile sliding bolster is placed on top of the sterile drape. The bolster can be adjusted for different angles of knee fl exion during surgery. PRODUCT NO’S: 2730 Base Dimensions: 20" x 10.5" PROUDLY MADE IN THE USA 16 WWW.INNOMED.NET I 1.800.548.2362 I NOVEMBER 2013
Kirschenbaum Foot Positioner Designed by Ira Kirschenbaum, MD Helps eliminate the use of sand bags under the drape during total knee surgery The foot rest is dome shaped for optimal foot contact and po si tion ing the leg in fl exion, and can be rotated. The unit can be used under the drape by attaching it to a standard table at tach ment or it can be ster il ized for use on top of the drape. It can be attached to the table with the optional sterilizable table clamp. Supplied with a removable, sterilizable silicone foot pad. PRODUCT NO’S: 2590 [Foot Positioner] 15.5" x 6" 2591 [Foot Positioner – Short] 9.5" x 6" Optional & Replacement Parts: 2590-P [Large Replacement Pad] 16" x 9" 2591-P [Small Replacement Pad] 9.5" x 9.25" 2595 [Optional Table Clamp] PROUDLY MADE IN THE USA Modifi ed 90° Leg Stabilizer Designed by Gregory Fanelli, MD Useful in arthroscopic knee surgery to hold the leg in position PRODUCT NO: Helps to open up the 2725 knee joint when pressure Post Height: 11.375" is applied to the lower Pad Length: 9" leg. Pad and sterilizable Pad Diameter: 3" table clamp included. Replacement Parts: 9120 [Table Clamp] PROUDLY MADE 8840-P [Pad] IN THE USA Leg Stabilizer Designed by Gregory Fanelli, MD Useful in arthroscopic knee surgery to hold the leg in position PRODUCT NO: Helps to open up the 8840 knee joint when pressure Overall Length: 18.5" is applied to the lower Handle Length: 9.25" leg. Sterilizable table Pad Diameter: 3" clamp included. Replacement Parts: 9120 [Table Clamp] PROUDLY MADE 8840-P [Pad] IN THE USA PROUDLY MADE IN THE USA Cherf Cast Stand Designed by John Cherf, MD Assists in applying short leg casts Designed to assist in ap ply ing short leg casts, the adjustable height permits optimal leg position for the seated patient and helps insure the ap pli ca tion of a cast with the foot/ankle at 90 degrees to the leg. The foot is placed on the tongue of the stand. Stock i nette is pulled over the foot and tongue. Cast padding and plaster/fi ber glass is used in a routine fashion. The cast stand is slipped forward dis en gag ing the foot after the cast has hard ened. PRODUCT NO: 2040 Base: 18.5" x 14.5" Height: Adjusts from 14" to 23.75" Foot Rest: 11" x 1.75" KNEE PRIMARY & REVISION INSTRUMENTS I 1.800.548.2362 I FREE TRIAL ON MOST INSTRUMENTS 17
Page 1 and 2: 11 2013 INSTRUMENTS FOR ORTHOPEDIC
Page 3 and 4: Designed to remain in position, wit
Page 5 and 6: Kaufman Gap Jack Assembly Designed
Page 7 and 8: Scott Patella Resection Guide/Clamp
Page 9 and 10: Intraarticular Tissue Grasper/Ronge
Page 11 and 12: Bhargava Modifi ed Meniscal Clamp L
Page 13 and 14: Stulberg Leg Positioner Designed by
Page 15: Fromm Femur & Tibia Triangles Desig
Page 19 and 20: Goytia Stackable Hohmann Retractors
Page 21 and 22: Hohmann Retractor Designed like the
Page 23 and 24: Two Sizes Available Harwin Modifi e
Page 25 and 26: MIS Modifi ed Wide PCL Retractor De
Page 27 and 28: Baldwin Lateral Soft Tissue Retract
Page 29 and 30: Minimally Invasive Knee Retractors
Page 31 and 32: Lachiewicz-Hoover Patella Retractor
Page 33 and 34: PRODUCT NO’S: 6216 [Hohmann] Over
Page 35 and 36: Trans-sulcus Angle Guide Helps esta
Page 37 and 38: Ring Curettes 3mm 6mm 8mm PRODUCT N
Page 39 and 40: Wide Offset Osteotome Designed by P
Page 41 and 42: Pin Inserter Used for 1/8" (3.2mm)
Page 43 and 44: OrthoVise Made of stainless steel,
Page 45 and 46: Soft Impact Mallets with Easy Grip
Page 47 and 48: Adjusting Blades To Fit Com po nent
Page 49 and 50: Burnishing Ends Left Turn Ends Set
Page 51 and 52: Curved Cement Osteotome For use in
Page 53 and 54: Cobb Elevators Ultra hard titanium
Page 55 and 56: Universal Bone Grafting/Impacting F
Page 57 and 58: Chuck Key Handle Snaps onto a stand
Page 59 and 60: PRODUCT NO: 3011 Overall Length: 13

Knee Retractor - Innomed, Inc.

Create successful ePaper yourself

Delete template?

Save as template?