Knee Retractor - Innomed, Inc.

More documents

Recommendations

Info

Bicos Meniscal Repair Retractor Designed by James Bicos, MD A popliteal retractor specifi cally designed for meniscal repair or access to the posterior knee Used when an inside out meniscal repair is indicated, the design facilitates retracting the posterior soft tissues of the popliteal fossa out of the way, allowing passage of meniscal repair needles. The retractor's compact design facilitates a minimally invasive incision. The unique shape helps capture the meniscal repair needles and direct them out of the posterior incision for easy grasping and repair. Incorporates a shiny body to help refl ect inside the posterior wound and aid in seeing and retrieving the needles. PRODUCT NO: 2731 Overall Length: 5" Depth: 1.625" Diameter: 28mm PROUDLY MADE IN THE USA PRODUCT NO: 4680 Overall Length: 8" Handle-to-bend Length: 7" Prong Width: 7.5mm | 17mm Gap | 7.5mm PROUDLY MADE IN THE USA Cook Patellar Retractor Designed by Marshall L. Cook, MD Designed for patellar retraction during ACL reconstruction using patellar bone-tendon-bone graft The retractor is wide with tines that are widely spaced for better straddling the proximal patellar pole. This gives better purchase and control of the patella, and retracts the skin medially and laterally, obviating the need for additional medial and lateral skin retractor. Lipscomb Meniscal Retractor Designed by A. Brant Lipscomb, Jr., MD, P.A. Designed to protect neurovascular structures during meniscal and extraarticular ligament repairs PRODUCT NO: 3740 Overall Length: 9" PROUDLY MADE IN THE USA Redler ACL Guide Wire Stabilizer Designed by M.R. Redler, MD The conical close-ended design helps insure that the guide wire tip remains captured and helps to minimize the chances of the guidewire slipping. The tempered nitrate coated steel head helps to minimize the risk of metal shavings being introduced into the joint while the guide wire position is maintained. Designed to work with all ACL instrument sets, the head of the ACL Guide Wire Stabilizer will easily fi t through any standard arthroscopic portal. PRODUCT NO: 5210 Overall Length: 9.5" Handle Length: 4" Cup Outside Diameter: 4mm Cup Inside Diameter: 2mm PROUDLY MADE IN THE USA Designed to control the guide wire used to direct the reaming or dilating of the tibial tunnel 32 WWW.INNOMED.NET I 1.800.548.2362 I NOVEMBER 2013
PRODUCT NO’S: 6216 [Hohmann] Overall Length: 10.5" Blade Width: 19mm (.75") Prong Length: 35mm (1.375") Prong Width at Tip: 5mm 6217 [Bent Rake] Overall Length: 8" Blade Width: 19mm (.75") 6218 [Standard Rake] Overall Length: 8.375" Blade Width: 19mm (.75") MADE IN THEUK Hohmann Retractor Bent Rake Retractor Rake Retractor Comfort Grip Handle Retractors Comfort grip ergonomic handle helps reduce fatigue and slippage Stanton Forward Army-Navy Retractor Designed by John L. Stanton, MD, FACS Designed to work as “tissue pushers”, helping to enhance exposure by allowing the surgeon or an assistant to push forward the opposite side of the wound while retracting (or not) the nearer side Helps to hold the wound open without having to reach around to the opposite side and become fatigued. PRODUCT NO’S: 4515-01 [Shallow] Overall Length: 9" Blade Offset from Handle: 2.625" Blade Width: 18mm Blade Depth: Shallow 25mm 4515-02 [Deep] Overall Length: 9" Blade Offset from Handle: 2.625" Blade Width: 18mm Blade Depth: Deep 43mm PROUDLY MADE IN THE USA Merchant Surgical Goniometer Designed by Alan Merchant, MD Designed to help assess frontal plane limb alignment or measure the Q angle The extended length can reach from the center of the knee to the femoral head or the anterior superior iliac spine. The collapsible stainless steel device is autoclavable. Collapsible and steam sterilizable. PROUDLY MADE IN THE USA PRODUCT NO: 2029 Overall Length: 41" Fully Extended 22.5" Folded in Half 12" Fully Collapsed Amstutz Angled Mirror Designed by Harlan C. Amstutz, MD Used for viewing hard-to-see areas PRODUCT NO’S: 4861 Overall Length: 8" Handle Length: 6.25" Mirror #1: 32x13mm Mirror #2: 19x16mm PROUDLY MADE IN THE USA KNEE PRIMARY & REVISION INSTRUMENTS I 1.800.548.2362 I FREE TRIAL ON MOST INSTRUMENTS 33
Page 1 and 2: 11 2013 INSTRUMENTS FOR ORTHOPEDIC
Page 3 and 4: Designed to remain in position, wit
Page 5 and 6: Kaufman Gap Jack Assembly Designed
Page 7 and 8: Scott Patella Resection Guide/Clamp
Page 9 and 10: Intraarticular Tissue Grasper/Ronge
Page 11 and 12: Bhargava Modifi ed Meniscal Clamp L
Page 13 and 14: Stulberg Leg Positioner Designed by
Page 15 and 16: Fromm Femur & Tibia Triangles Desig
Page 17 and 18: Kirschenbaum Foot Positioner Design
Page 19 and 20: Goytia Stackable Hohmann Retractors
Page 21 and 22: Hohmann Retractor Designed like the
Page 23 and 24: Two Sizes Available Harwin Modifi e
Page 25 and 26: MIS Modifi ed Wide PCL Retractor De
Page 27 and 28: Baldwin Lateral Soft Tissue Retract
Page 29 and 30: Minimally Invasive Knee Retractors
Page 31: Lachiewicz-Hoover Patella Retractor
Page 35 and 36: Trans-sulcus Angle Guide Helps esta
Page 37 and 38: Ring Curettes 3mm 6mm 8mm PRODUCT N
Page 39 and 40: Wide Offset Osteotome Designed by P
Page 41 and 42: Pin Inserter Used for 1/8" (3.2mm)
Page 43 and 44: OrthoVise Made of stainless steel,
Page 45 and 46: Soft Impact Mallets with Easy Grip
Page 47 and 48: Adjusting Blades To Fit Com po nent
Page 49 and 50: Burnishing Ends Left Turn Ends Set
Page 51 and 52: Curved Cement Osteotome For use in
Page 53 and 54: Cobb Elevators Ultra hard titanium
Page 55 and 56: Universal Bone Grafting/Impacting F
Page 57 and 58: Chuck Key Handle Snaps onto a stand
Page 59 and 60: PRODUCT NO: 3011 Overall Length: 13

Knee Retractor - Innomed, Inc.

Create successful ePaper yourself

Delete template?

Save as template?