D R I E – D Lagertechniek bv DATA SHEETS

More documents

Recommendations

Info

DRIE-D Lagertechniek bv the right perspective Kiotoweg 120, 3047 BG, Rotterdam, NL telephone: (+31) 10 - 462 07 00 telefax: (+31) 10 - 462 07 07 E-mail: mail@drie-d.nl internet: www.drie-d.nl D-GLIDE SPHERICALS Application D-glide Sphericals are spherical bearings made both to international standards as well as designed for purpose. They consist of a D-glide ‘sphere’ fitted with a stainless steel sleeve which together form the inner part that moves inside a stainless steel housing. Because of the combination of materials used they are maintenance free as well as corrosion free and can be used dry as well as submerged in (sea) water and almost all other fluids. Load ratings are on a similar level to steel-onsteel or other maintenance free bearings. Typical applications: hydraulic cylinders, (sluice) doors, draw-bridges. Advantages of the D-glide solution - maintenance free - usable in any environment, wet and dry - interchangeable with other spherical bearings - different properties easily possible (larger angles, other material combinations, etcetera) - maximum reliability (no external provisions needed) - both radial and axial versions available Files D-glide Sphericals, 1.jpg: D-glide Sphericals, 2.jpg: A collection of both standard and custom build D-glide Sphericals, i.a.:special 27° tilt angle bearings for aircraft simulators. Type 320 D-glide Sphericals used in hydraulic cylinders in a ‘split hopper dredger’, more than 4 times outlasting both lubricated steel-on-steel and other maintenance free ones. D-glide Sphericals, Axial, 1.jpg: D-glide Spherical thrust bearings, ø260 and ø280 for Flender transmission cutter dredger data sheets UK, D-glide complete, 2008, page 12
DRIE-D Lagertechniek bv the right perspective Kiotoweg 120, 3047 BG, Rotterdam, NL telephone: (+31) 10 - 462 07 00 telefax: (+31) 10 - 462 07 07 E-mail: mail@drie-d.nl internet: www.drie-d.nl D-GLIDE ‘NON-SPHERICALS’ Application Spherical bearings are used a lot in the eyes if hydraulic cylinders and many other joints and hinges where the alignment of shaft and housing can not be guaranteed. In wet and dirty environments it is difficult to keep these bearings (both the lubricated as well as the maintenance free ones) in a good condition. Seals and lubrication must be in a perfect condition in order to keep the bearings alive. In many of these application the maximum misalignment angles are limited. If (in general) these angles are limited to no more than 0.5° they can be replaced by D-glide bushings in one piece with the same dimensions and geometry. The flexibility of the bearings is sufficient to cope with the misalignment. The result is a inexpensive, reliable bearing, without moving parts and without the need for external provisions like seals or lubrication. Advantages of the D-glide solution - no moving parts - easy installation - no corrosion - very low cost - short delivery times Files Various D-glide F parts, 3.jpg: Shipping, 1.jpg: Picture of ‘D-glide Non-Sphericals’ replacing the spherical bearings with the same dimensions D-glide bearings in the joints and hydraulic cylinders of deck hatches. data sheets UK, D-glide complete, 2008, page 13
Page 1: D R I E - D Lagertechniek bv the ri
Page 4 and 5: DRIE-D Lagertechniek bv the right p
Page 26: DRIE-D Lagertechniek bv the right p

D R I E – D Lagertechniek bv DATA SHEETS

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?