Coin changer - National Rejectors Inc. GmbH

More documents

Recommendations

Info

Ca s h a c c e p ta n c e c 2 Configuration Limiting acceptance of tube coins (filling level limitation) Quick approach: The changer can be configured so that each change tube accepts no more than a specific number of coins. When this number of coins is reached in a tube, all further coins for this tube are then directed into the cash-box temporarily. Only when coins have been paid out of this tube, coins are again sorted into the tube. If this function is not used (setting "000"), the upper filling level sensor (full sensor) of the tubes determines, irrespective of the number of coins, from when the coins will be sorted into the cash-box and no longer into the tubes. To configure the filling level limitation: = Main menu > E = Settings > Coin settings > Filling level limitation Press key ... How often? Effect 1 1 x You enter the main menu 2 1 x You enter the Se t t i n g menu 3 until Coin settings You want to enter submenu Co i n s e t t i n g s 4 1 x You enter the submenu 5 until Filling level limitation You want to enter submenu Filling l e v e l limitation 6 1 x You enter the submenu 7 / 8 1 x until tube desired You want to set a filling level limitation for this tube Now you can set a limitation for this tube 9 / until required digit You highlight the digit to be set 10 until required value This value is to be set / Please repeat steps 9 and 10 to set the other two digits of the filling level limitation, if 11 necessary 12 1 x You lock the set filling level limitation in memory 13 Please repeat steps 7 to 12 to set the filling level limitations of the other tubes, if necessary 14 1 x/2 x You return to main menu/operating mode 32 National Rejectors, Inc. GmbH, Buxtehude
c 2 Configuration Ca s h a c c e p ta n c e Inhibiting coins Quick approach: If you want certain coins to be no longer accepted for payment at the machine, you may inhibit these coins (temporarily). The coin changer stores the coins 1–16 in ascending coin value order, i.e. "coin 01" is always the lowest-value and "coin 16" always the highest-value coin programmed. To inhibit/release a certain coin: = Main menu > E = Settings > Inhibit mask > Inhibit mask Press key ... How often? Effect 1 1 x You enter the main menu 2 1 x You enter the Se t t i n g menu 3 until Inhibit mask You want to enter submenu In h i b it m a s k 4 1 x You enter the submenu. The required menu item has already been selected 5 1 x You want to inhibit/release a coin 6 / until coin desired You want to inhibit/release this coin 7 1 x Now you can inhibit/release this coin 8 / until setting desired You want this coin to be inhibited/ released 9 1 x You lock the setting in memory 10 1 x/2 x You return to main menu/operating mode National Rejectors, Inc. GmbH, Buxtehude 33
Page 1: Technical Documentation Coin change
Page 4 and 5: Ta b l e o f c o n t e n t s c 2 Co
Page 6 and 7: Ta b l e o f c o n t e n t s c 2 Co
Page 8 and 9: Ab o u t t h e m a n u a l c 2 Conf
Page 10 and 11: Ge n e r a l i n f o r m at i o n c
Page 12 and 13: Pr e s e t t i n g s c 2 Configurat
Page 14 and 15: Se t t i n g s f o r filling a n d
Page 24 and 25: Pr i c e s a n d v e n d i ng m o d
Page 30 and 31: Ca s h a c c e p ta n c e c 2 Confi
Page 40 and 41: Ch a n g e pay o u t c 2 Configurat
Page 46 and 47: Pe r i p h e r a l c 2 Configuratio
Page 62 and 63: Au d it c 2 Configuration To set th
Page 64 and 65: Au d it c 2 Configuration Specifyin
Page 66 and 67: Audit c 2 Configuration Selecting t
Page 68 and 69: Ba s i c s e t t i n g s c 2 Config
Page 76 and 77: Bat c h c o n f ig u r at i o n c 2
Page 78 and 79: Bat c h c o n f ig u r at i o n c 2
Page 80 and 81: In d e x c 2 Configuration Chapter
Page 82 and 83:
In d e x c 2 Configuration M Machin
show all

Coin changer - National Rejectors Inc. GmbH

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?