70 Series Connection Manual - Automation Service Srl

More documents

Recommendations

Info

SanDisk and SanDisk logos are registered trademarks of SanDisk Corporation, U.S.A. MELDAS is a registered trademark of Mitsubishi Electric Corporation. Other company and product names that appear in this manual are registered trademarks or trademarks of their respective companies.
Introduction This manual is called MITSUBISHI CNC 70 Series CONNECTION MANUAL and covers the items related to installation, connection and maintenance of this NC unit. Read this manual thoroughly before using. For safe use, fully understand "Precautions for Safety" on the next page first. Details described in this manual: CAUTION For items described as "Restrictions" or "Usable State" in this manual, the instruction manual issued by the machine tool builder takes precedence over this manual. Items that are not described in this manual must be interpreted as "not possible". This manual is written on the assumption that all option functions are added. Confirm the specifications issued by the machine tool builder before use. Refer to the Instruction Manual issued by each machine tool builder for details on each machine tool. Some screens and functions may differ depending on each NC system (or version), and some functions may not be possible. Please confirm the specifications before use. The numerical control unit is configured of the control unit, display unit, operation board, servo drive unit, spindle drive unit, power supply unit + driver, servomotor, and spindle motor, etc. In this manual, the following items are generically called the "controller". • Control unit • Display unit • Operation board • Numerical control unit peripheral devices (input/output unit, safety unit) In this manual, the following items are generically called the "drive unit". • Servo drive unit • Spindle drive unit • Power supply unit + driver In this manual, the following items are generically called the "motor". • Servomotor • Spindle motor
Page 4 and 5: Precautions for Safety Always read
Page 6 and 7: 2. Items related to prevention of f
Page 8 and 9: CAUTION The controller, drive unit
Page 10 and 11: (3) Adjustments CAUTION Check and a
Page 12 and 13: (6) Maintenance, inspection and par
Page 14 and 15: 5.6 Manual Pulse Generator.........
Page 16 and 17: 3.1.9 Ethernet Connector (LAN).....
Page 18 and 19: 1. Introduction 1. Introduction Thi
Page 20 and 21: 2. System Configuration 2.2 General
Page 22 and 23: 2. System Configuration 2.3 List of
Page 24 and 25: 3. General Specifications (Environm
Page 26 and 27: 3. General Specifications (Environm
Page 28 and 29: 4. Outline Drawing 4.1 Control Unit
Page 30 and 31: 4. Outline Drawing 4.2 Display Unit
Page 32 and 33: 4. Outline Drawing 4.3 Operation Pa
Page 34 and 35: 4. Outline Drawing 4.5 Remote I/O U
Page 36 and 37: 4. Outline Drawing 4.6 Card-sized I
Page 38 and 39: 5. Panel Cut Dimension Drawing / In
Page 48 and 49: 6. Connections of Control Unit 6.1
Page 50 and 51: 6. Connections of Control Unit 6.2
Page 52 and 53:
6. Connections of Control Unit 6.4
Page 54 and 55:
Page 56 and 57:
6. Control Unit Connections 6.7 Con
Page 58 and 59:
6. Control Unit Connections 6.8 Con
Page 60 and 61:
Page 62 and 63:
7. Connections of Operation Panel I
Page 64 and 65:
Page 66 and 67:
Page 68 and 69:
Page 70 and 71:
Page 72 and 73:
Page 74 and 75:
8. Connections of I/O Interface 8.1
Page 76 and 77:
Page 78 and 79:
Page 80 and 81:
Page 82 and 83:
Page 84 and 85:
Page 86 and 87:
Page 88 and 89:
Page 90 and 91:
Page 92 and 93:
Page 94 and 95:
Page 96 and 97:
Page 98 and 99:
Page 100 and 101:
Page 102 and 103:
Page 104 and 105:
9. Basic Wiring for Servo Drive Uni
Page 106 and 107:
Appendix 1. EMC Installation Guidel
Page 108 and 109:
Page 110 and 111:
Page 112 and 113:
Page 114 and 115:
Page 116 and 117:
Appendix 2. Cable (Note 1) Lengths
Page 118 and 119:
Appendix 2. Cable 2.2 F034/F035 Cab
Page 120 and 121:
Appendix 2. Cable 2.5 F120 Cable 2.
Page 122 and 123:
Appendix 2. Cable 2.9 F351 Cable 2.
Page 124 and 125:
Appendix 2. Cable 2.11 G023/G024 Ca
Page 126 and 127:
Appendix 2. Cable 2.13 G301 Cable 2
Page 128 and 129:
Appendix 2. Cable 2.17 G430 Cable 2
Page 130 and 131:
Appendix 2. Cable 2.19 FCUA-R050/R0
Page 132 and 133:
Appendix 2. Cable 2.23 SH41 Cable 2
Page 134 and 135:
Appendix 3. Connectors 3.1 Connecto
Page 136 and 137:
Page 138 and 139:
Page 140 and 141:
Appendix 4. Servo/Spindle Cable and
Page 142 and 143:
Page 144 and 145:
Page 146 and 147:
Page 148 and 149:
Page 150 and 151:
Page 152 and 153:
Page 154 and 155:
Page 156 and 157:
Page 158 and 159:
Page 160 and 161:
Page 162 and 163:
Page 164 and 165:
Page 166 and 167:
Page 168 and 169:
Page 170 and 171:
Page 172 and 173:
Page 174 and 175:
Page 176 and 177:
Page 178 and 179:
Page 180 and 181:
Page 182 and 183:
Page 184 and 185:
Appendix 6. Precautions for Wiring
Page 186 and 187:
Page 188 and 189:
Page 190 and 191:
Page 192 and 193:
Appendix 7. Transportation Restrict
Page 194 and 195:
Page 196 and 197:
Page 198 and 199:
Appendix 8. Precautions for Complia
Page 200 and 201:
Revision History Date of revision M
Page 202:
Notice Every effort has been made t
show all

70 Series Connection Manual - Automation Service Srl

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?