70 Series Connection Manual - Automation Service Srl

More documents

Recommendations

Info

5. Panel Cut Dimension Drawing / Installation Dimension Drawing 5.6 <strong>Manual</strong> Pulse Generator 5.6.2 HD60 ø77±0.5 3.6 Packing t2.0 ø80±1 3-M4 stud bolt L10 12V 0V A B ø60±0.5 16 24 27±0.5 ø60±0.5 8.89 7.60 Installation of screws other than M3 x 6 not possible [Panel cut drawing] (Divide equally by three) 120° 3-ø4.8 ø62 +2 0 ø72±0.2 29
5. Panel Cut Dimension Drawing / Installation Dimension Drawing 5.7 Synchronous Feed Encoder 5.7 Synchronous Feed Encoder 5.7.1 OSE-1024-3-15-68 Caution plate 68 56 ø68 -0.009 -0.025 ø50 68 56 4-ø5.4 hole 20 2 28 5 3 19. 5 102 135 33 ø14.3 0 -0.11 2 ø15 -0.006 -0.017 5 -0.012 -0.042 ø16 3 +0. 1 0 +0. 14 +0. 14 1.15 0 1.15 0 26 ø50 -0.009 -0.025 Cross section BB Valid depth of key groove is 21mm 2 Enlarged drawing of key 30
Page 2 and 3: SanDisk and SanDisk logos are regis
Page 4 and 5: Precautions for Safety Always read
Page 6 and 7: 2. Items related to prevention of f
Page 8 and 9: CAUTION The controller, drive unit
Page 10 and 11: (3) Adjustments CAUTION Check and a
Page 12 and 13: (6) Maintenance, inspection and par
Page 14 and 15: 5.6 Manual Pulse Generator.........
Page 16 and 17: 3.1.9 Ethernet Connector (LAN).....
Page 18 and 19: 1. Introduction 1. Introduction Thi
Page 20 and 21: 2. System Configuration 2.2 General
Page 22 and 23: 2. System Configuration 2.3 List of
Page 24 and 25: 3. General Specifications (Environm
Page 26 and 27: 3. General Specifications (Environm
Page 28 and 29: 4. Outline Drawing 4.1 Control Unit
Page 30 and 31: 4. Outline Drawing 4.2 Display Unit
Page 32 and 33: 4. Outline Drawing 4.3 Operation Pa
Page 34 and 35: 4. Outline Drawing 4.5 Remote I/O U
Page 36 and 37: 4. Outline Drawing 4.6 Card-sized I
Page 38 and 39: 5. Panel Cut Dimension Drawing / In
Page 48 and 49: 6. Connections of Control Unit 6.1
Page 56 and 57: 6. Control Unit Connections 6.7 Con
Page 58 and 59: 6. Control Unit Connections 6.8 Con
Page 62 and 63: 7. Connections of Operation Panel I
Page 74 and 75: 8. Connections of I/O Interface 8.1
Page 96 and 97:
8. Connections of I/O Interface 8.3
Page 98 and 99:
Page 100 and 101:
Page 102 and 103:
Page 104 and 105:
9. Basic Wiring for Servo Drive Uni
Page 106 and 107:
Appendix 1. EMC Installation Guidel
Page 108 and 109:
Page 110 and 111:
Page 112 and 113:
Page 114 and 115:
Page 116 and 117:
Appendix 2. Cable (Note 1) Lengths
Page 118 and 119:
Appendix 2. Cable 2.2 F034/F035 Cab
Page 120 and 121:
Appendix 2. Cable 2.5 F120 Cable 2.
Page 122 and 123:
Appendix 2. Cable 2.9 F351 Cable 2.
Page 124 and 125:
Appendix 2. Cable 2.11 G023/G024 Ca
Page 126 and 127:
Appendix 2. Cable 2.13 G301 Cable 2
Page 128 and 129:
Appendix 2. Cable 2.17 G430 Cable 2
Page 130 and 131:
Appendix 2. Cable 2.19 FCUA-R050/R0
Page 132 and 133:
Appendix 2. Cable 2.23 SH41 Cable 2
Page 134 and 135:
Appendix 3. Connectors 3.1 Connecto
Page 136 and 137:
Page 138 and 139:
Page 140 and 141:
Appendix 4. Servo/Spindle Cable and
Page 142 and 143:
Page 144 and 145:
Page 146 and 147:
Page 148 and 149:
Page 150 and 151:
Page 152 and 153:
Page 154 and 155:
Page 156 and 157:
Page 158 and 159:
Page 160 and 161:
Page 162 and 163:
Page 164 and 165:
Page 166 and 167:
Page 168 and 169:
Page 170 and 171:
Page 172 and 173:
Page 174 and 175:
Page 176 and 177:
Page 178 and 179:
Page 180 and 181:
Page 182 and 183:
Page 184 and 185:
Appendix 6. Precautions for Wiring
Page 186 and 187:
Page 188 and 189:
Page 190 and 191:
Page 192 and 193:
Appendix 7. Transportation Restrict
Page 194 and 195:
Page 196 and 197:
Page 198 and 199:
Appendix 8. Precautions for Complia
Page 200 and 201:
Revision History Date of revision M
Page 202:
Notice Every effort has been made t
show all

70 Series Connection Manual - Automation Service Srl

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?