Screen E-Book (.PDF) - MacDermid Autotype

More documents

Recommendations

Info

Problem solving GuideTechnical referenceSee ‘Getting the right exposure’ chapter.SolutionPositive and stencil surface must be cleanbefore exposure. Use a clean room wipe orTeknek roller.Printed line/dot larger than positiveDescriptionPrinted line/dot wider than positive.Cause1. Ink slump.2. Sawtooth.Technical reference1. See ‘Optional theory’ chapter.2. See ‘Problem solving in the real world’chapter.Solution1. Change the ink.2. See Sawtooth problem in this guide.Printed line/dot smaller than positiveDescriptionPrinted line/dot smaller than positive.CauseUndercutting causing reduced image sizeon the stencil.1. Wrong lamp geometry.Rz 4.52. Poor vaccum.3. Positive upside down.4. Backing sheet not removed.Rz 22.5130
5. Over exposure.Poor washout of the stencil causing reducedimage size of the stencil.1. Low washout pressure.2. Stencil fogged by heat or light.3. Low density positive.Technical referenceSee ‘Getting the right exposure’ chapter.Solution1. Optimise exposure conditions.2. Optimise washout conditions, moststencils will benefit from washing out witha high pressure gun from 1m distance.SolutionReduce the EOM of the stencil. Capillex CXand Capillex CP give controlled low EOMstencils designed to resolve this problem.Image distortionDescriptionUnable to register multicolour prints orchange in the size of the print across thestencil.CauseThick edges to printDescriptionThick image edge.CauseStencil EOM too high.Technical referenceSee ‘Problem solving in the real world’chapter.1. Off contact too high.2. Squeegee pressure too high.3. Image too close to the screen edge.4. <strong>Screen</strong>s of different tension.5. Too flexible mesh choice for the job.131
Page 1 and 2:
HowHow to be agreat ScreenprinterEd
Page 3:
About this eBookI’m passionate ab
Page 6:
06Table ofContents07 The Theory Bit
Page 11 and 12:
The wrong way: a strong-deep flood.
Page 13 and 14:
why a light flood is recommended so
Page 15:
This is the single most important f
Page 18 and 19:
When I first pointed this out to my
Page 20 and 21:
The Theory Bit20Why is the 1-2-3 so
Page 22 and 23:
The mesh does the meteringThe 1-2-3
Page 24 and 25:
This gives us the ‘real’ TIV fo
Page 26 and 27:
simple, in-control process.Years of
Page 28 and 29:
The Optional Theory28At the shear r
Page 30 and 31:
I’ve come across examples in all
Page 32 and 33:
The Optional TheoryOur 50µm line b
Page 34 and 35:
oughness can slow slumping; it prob
Page 36 and 37:
The Optional TheoryThe exact part o
Page 38 and 39:
atches of the ‘same’ mesh. My f
Page 40 and 41:
The Optional Theory40The industry r
Page 42 and 43:
the screen frame itself to compensa
Page 44 and 45:
Print Faults - Making and fixing th
Page 46 and 47:
Print FaultsThey include tape marks
Page 48 and 49:
Wrong ink - Too much viscous drag (
Page 50 and 51:
DustPrint FaultsWe threw some dust
Page 52 and 53:
What’s the best order to print yo
Page 54 and 55:
Colour shifts54high-frequency (non-
Page 56 and 57:
We formed our own (subjective) opin
Page 58 and 59:
And the winner is...Colour shifts58
Page 60 and 61:
Getting the right exposureAnna Harr
Page 62 and 63:
Getting the right exposureThe light
Page 64 and 65:
3/4 full exposureEFFECTS: Emulsion
Page 66 and 67:
Getting the right exposureThere is
Page 68 and 69:
Undercutting from a rough stencilSo
Page 70 and 71:
Getting the right exposure(or numbe
Page 72 and 73:
Solving problems in the real worldA
Page 74 and 75:
Solving problemsThe simple act of r
Page 76 and 77:
Emulsion coatingThe advice about cl
Page 78 and 79:
Solving problemsA quick tip to help
Page 80 and 81: stencil causes a thick edge needed
Page 82 and 83: Solving problemsThis screen-shot fr
Page 84 and 85: A modest Rz gives amodest absolute
Page 86 and 87: Solving problemsThe root cause of n
Page 88 and 89: Now the ink fully fills the extra s
Page 90 and 91: Solving problems90Stencil X gives b
Page 92 and 93: Moiré, causes and curesSteven Abbo
Page 94 and 95: Moire, causes and cures94fluential
Page 96 and 97: Figure ii. The overlayedpattern fro
Page 98 and 99: Moire, causes and cures98Causes and
Page 100 and 101: 2 15° moiréIt’s an unfortunate
Page 102 and 103: Moire, causes and cureson top of an
Page 104 and 105: Ideal. Find a RIP with an option fo
Page 106 and 107: Moire, causes and curescan’t pick
Page 108 and 109: frequency tend to have a lower ampl
Page 110 and 111: Moire, causes and curesis a half-tr
Page 112 and 113: Incidentally, note that the ratio o
Page 114 and 115: Moire, causes and cures114So, surpr
Page 116 and 117: grid) in a conventional set that wa
Page 118 and 119: Moire, causes and cures118what this
Page 120 and 121: Arguably the skipping takes place p
Page 122 and 123: Moire, causes and curesSummaryAs Ma
Page 124 and 125: MoiréDescriptionAn unexpected patt
Page 126 and 127: Problem solving GuideCause1. The mo
Page 128 and 129: Dark spots / HickiesDescriptionDark
Page 132 and 133: 6. Substrate unstable.7. Changes in
Page 134 and 135: Glossary of terms used in this eBoo
Page 136 and 137: Glossary136Moiré amplitudeThe ampl
Page 138: A Macdermid Autotype HowTo eBookEdi
show all

Screen E-Book (.PDF) - MacDermid Autotype

Create successful ePaper yourself

Delete template?

Save as template?