MODEL 5204 - Silent Knight

More documents

Recommendations

Info

Control Panel Installation5.4 Battery ConnectionNote: When using two batteries, it is recommended that they be of the same ampere hour (AH) rating and approximatelythe same age.Battery cable connectors enable installation of one or two 12 VDC, 17 A rechargeablebatteries. Two sets of battery leads are provided for battery connection. When connecting asingle battery, connect one of the red leads to the positive side of the battery. Connect a blacklead to the negative side of the battery.If using a second battery, connect the remaining lead to the positive side of the second battery.Connect the remaining black lead to the negative side of the second battery.5.5 Mounting the 5204Read the environmental specifications in Section 2.2 before mounting the 5204 panel.The panel should be accessible to “Main Drop” wiring runs. The 5204 panel should bemounted as close to the center of the building as possible and located within a secured area,but should be accessible for testing and service. End-users responsible for maintaining thepanel should be able to hear alarms and troubles. When selecting a location, keep in mind thatthe panel itself is the main source of alarm and trouble annunciation.Mount the 5204 so it is firmly secured to the wall surface. When mounting the 5204 onconcrete, especially when moisture is expected, attach a piece of 3/4-inch plywood to theconcrete surface and then attach the 5204 to the plywood. Also mount any other desiredcomponents (such as external printer) to the plywood. If you will be flush mounting thecabinet, the hole for the enclosure should be 14 1/2” x 19 1/8” (width x length of box only).Do NOT flush-mount in a wall designated as a fire break.5.6 Terminal Strip DescriptionThe terminal strips on the PC board are nonremovable. Table 5-1 below lists the function andelectrical rating of each terminal. Note the following:• The total load of all devices attached to the system must not exceed 3.0 A.• Alarm polarity is shown for bells (terminals 7-10). Normal polarity is the opposite.• Terminals 22 and 26 are the only terminals that should be used to return smoke power, andthey should not be used for any other purpose.150644 5-3
Model 5204 Fire Control/Communicator Installation ManualImportant!The 5204 emits a hum that is not noticeable to most end users unless they are nearthe panel in a very quiet environment.TerminalNumberTable 5-1: Terminal Strip DescriptionNote: Combined smoke power maximum capacity is 1000 mA.Nominal VDC Output(“System Normal” Condition)Terminal Description12 V Mode 24 V Mode1* Auxiliary Power (+) - 1500 mA max. 13.65 27.32* Ground 0 03* Annunciator Power (+) - 500 mA max. 13.5 13.64* Serial Annunciator Data Out (SKO) 9.1 9.25* Serial Annunciator Data In (SKI) 6.6 6.76* External Silence Switch or Alarm Reset 8.6 8.67 Bell 1 - 1500 mA max. 5.0 10.08 Bell 1 + 0.95 1.99 Bell 2 - 1500 mA max. 5.0 10.010 Bell 2 + 0.95 1.911 Relay 1 Normally Open N/A N/A12 Relay 1 Common N/A N/A13 Relay 1 Normally Closed N/A N/A14 Relay 2 Normally Open N/A N/A15 Relay 2 Common N/A N/A16 Relay 2 Normally Closed N/A N/A17* Auxiliary Power - 175 mA 13.64 13.7718* Zone 1 (Class B/Style B) Input 0.08 0.1619* Smoke Power 13.65 27.320* Zone 2 (Class B/Style B) Input 0.08 0.1621* Smoke Power 13.65 27.322* Ground 0 023* Zone 3 (Class B/Style B) Input 0.08 0.1624* Smoke Power 13.65 27.325* Zone 4 (Class B/Style B) Input 0.08 0.1626* Ground 0 0* Power-limited5-4 150644
Page 5 and 6: Model 5204 Fire Control/Communicato
Page 21: Model 5204 Fire Control/Communicato
Page 27: Model 5204 Fire Control/Communicato
Page 73 and 74:
Model 5204 Fire Control/Communicato
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
• A new or refurbished board will
show all

MODEL 5204 - Silent Knight

Create successful ePaper yourself

Delete template?

Save as template?