Electrical Plan Review Submittal Guide / Checklist - City of Bellevue

More documents

Recommendations

Info

____ Wiring methods for the fire alarm system.____ Show all emergency system wiring methods pertaining to the smoke control.____ Schedule of individual smoke control components starting loads that will start at the same time____ Schedule of individual smoke control components running loads.____ The total combined loads of smoke control components for start up and run (start up and run shownseparately).____ Identify the color marking, protection, and routing of the conduit from the generator to the pressurizationfan(s).Arc Flash Calculation____ Provide: (1) the incident energy level calculation in cal/cm squared at 18” from the flash hazard; (2) theflash hazard category, and (3) the flash hazard boundary for each service, distribution board, and panel(4) the date the arc flash calculation was done.Provide this in a cascading format relating to the one line or riser showing:- the device rating and identification- the voltage- the arc gap- the bolted fault current or the available fault currentThe nomenclature used must match the one line diagram for panel/ distribution identification. Please see COBordinance 110.16. http://www.mybuildingpermit.com/Misc/WA%20Cities%20Elect%20Code%2011-12-09.pdfVerification of the calculation will not be required where it is stamped and signed by an electrical engineercurrently licensed in the State of Washington.An exception allows no flash hazard analysis where all the following conditions exist:- The circuit is rated 240volts or less- The circuit is supplied by one transformer- The transformer supplying the circuit is rated less than 125kvaElectric Vehicle Charging Systems____ Provide the level of the supply equipment____ Site or floor plan with location of the system including physical protection specifics if required____ Conduit and conductor sizes to the outlets or equipment____ Ratings of equipment____ Panel schedule with demand and connected loadPhotovoltaic Systems____ One line diagram of the system showing conduit and conductor sizes, connection to the existing service,overcurrent size(s)____ Grounding electrode conductor sizes and location of connection(s) to the system____ Where the inverter(s) is physically located____ Plan view of the array layout on the roof (clearly showing setbacks from the roof edge and peak)____ Spec sheet showing the power ratings etc.____ Penetration location of the conductors into the house or attic____ Derating calculation of the conductors on the roof and/or in the attic8
Revisions made after Plans approval____ Provide revision symbols (clouds or other effective means) around changes with something to indicatethe date it was changed. These need to stay on the plans throughout the project.____ Provide descriptions of specific changes that are proposed in the revised areasEmergency and Legally Required Systems Equipment(what type equipment needs to be on which system)TABLE 403(1)STANDBY (LEGALLY REQUIRED) AND EMERGENCY POWERType of EquipmentMaximumTime toEnergizeLoadsMinimum RunTime (Duration)IBC SectionIFC or NFPASectionEmergency Power Systems 1604.2.15 HighrisesExit signs10 seconds2 hours forgenerator power;1011.5.3or 90 minutes forbattery backup604.2.16Undergroundbuildings1011.5.32403.12.6.1Temporary tents,canopies,membranestructures1006.3Exit illumination 10 seconds 8 hours 1006.3604.2.15 Highrises604.2.16Underground9
Page 1 and 2: Electrical Plan ReviewSubmittal Gui
Page 3 and 4: Checklist - Electrical Plan ReviewT
Page 5 and 6: Floor Plan (Lighting)____ Electrica
Page 7: ____ On a high rise building, if th
Page 11 and 12: Smokeproof enclosures and elevator
Page 13 and 14: Reminders and Notes- The seismic br
Page 15: Fault Current Calculation Form, p.2
Page 18: Sample 3Ø Panel Schedule18

Electrical Plan Review Submittal Guide / Checklist - City of Bellevue

Create successful ePaper yourself

Delete template?

Save as template?