GEA COM4plus - CS Klimateknik

More documents

Recommendations

Info

Installation and AssemblyGEA COM4plusMounting cover panels and switch box hood for outdoor installation.Fig. 5-16: COM4plus outdoor installation1: Unit cover panels2: Switch box hood (fold-away)3: Cable duct4: Middle panel (with opening for switch box)32 PR-2009-0022-GB • Subject to modifications • Status 04/2009
GEA COM4plusInstallation of Components and Accessories6 Installation of Components and AccessoriesIn line with the connection of heat exchangers, humidifiers etc., the coil connectionmay only be carried out by specialists with the necessary knowledge of relevantaccident prevention regulations and other standard regulations relevantto health and safety in the workplace, based on their training and experience.DAMAGE TO THE UNIT!When mounting GEA CompactLine units care must be taken to ensure that noloads are applied to the floor panels. During installation work suitable measuresshould be taken to ensure that all loads are spread across the bottom profiles(e.g. using grid walkways).6.1 Prerequisites• Check the unit for external damage and check whether it has been properlyassembled and anchored.• Check whether anti-vibration and structure-borne sound attenuating mats havebeen provided. This means that either:– The foundation has been isolated from the unit using rubber plates (for example)where the unit is installed on level ground and no special structure-borne sound isolationrequirements exist;– or, in the case of ceiling mounting, commercially available spring elements havebeen used;– or, where very special acoustic requirements exist, an acoustics engineer has beenconsulted when selecting the most suitable structure-borne sound attenuationmethod.• Before you start with the coil connection, check the following:– Drain valves must be installed at all low points in the water system to ensure thatthe water circuit can be fully drained in order to carry out maintenance or repairs.– A water drain with shut-off valve must be installed in order to drain the unit’s watersystem.– Air vents must be installed at all the high points of the water system at easily accessiblelocations.• Ensure that the piping system is flushed through until it is clean by others and acleaning record compiled.6.2 Installation of air control and air conveying componentsIn order to prevent the transmission of structure-borne sound, a tension-free connectionbetween air ducts and the unit must be made using elastic connectorsor structure-borne sound attenuators(also refer to „Structure-borne sound attenuation“ on page 26).If you are connecting air ducts to the units via flexible connectors, the installation lengthof the connectors must be less than their extended length.PR-2009-0022-GB • Subject to modifications • Status 04/2009 33
Page 3 and 4: GEA COM4plusProduct Type Code1 Prod
Page 5: GEA COM4plusSafety and User Informa
Page 8 and 9: Safety and User InformationGEA COM4
Page 10 and 11: Technical DescriptionGEA COM4plus3
Page 12 and 13: Technical DescriptionGEA COM4plusAi
Page 14 and 15: Technical DescriptionGEA COM4plus3.
Page 20 and 21: Transport and StorageGEA COM4plus4
Page 22 and 23: Transport and StorageGEA COM4plus4.
Page 24 and 25: Installation and AssemblyGEA COM4pl
Page 34 and 35: Installation of Components and Acce
Page 36 and 37: Installation of Components and Acce
Page 38 and 39: Electrical ConnectionGEA COM4plus7.
Page 40 and 41: Electrical ConnectionGEA COM4plus7.
Page 42 and 43: Commissioning and TestingGEA COM4pl
Page 54 and 55: Disassembly and DisposalGEA COM4plu
Page 56: Customer proximity, sales structure

GEA COM4plus - CS Klimateknik

Create successful ePaper yourself

Delete template?

Save as template?