II PRO PLUS Snowplow #64750/64999/66901/66974/66980

More documents

Recommendations

Info

INSTALLATION INSTRUCTIONSSNOWPLOW ASSEMBLY WITH PRO PLUS ® BLADEBlade GuideAssemblyPRO PLUS BladeLift Arm5/8" Nuts5/8" x 4"EyeboltUpperLift FrameBumperPad3/4"Washers3/4" x 3-1/4"Clevis PinsTrip StopCushionShockAbsorber3/4" x 4"Clevis Pin5/32" x 1-1/2"Cotter PinsQuadrantBladeBracketsTripSpring3/4" x 4"Clevis PinSpringShock BracketsAbsorberBracketsCylinderBracket3/4"Washer5/32" x 1-1/2"Cotter PinLowerLift FrameChainAssemblyStandA-FrameStandShoePivotPlatesPivot BarPivot PinsLit. No. 66897, Rev. 07 6 June 15, 2010
INSTALLATION INSTRUCTIONSQUADRANT TO BLADE1. Lay the blade face down on some cardboard onthe fl oor to protect the fi nish.2. Assemble the quadrant to the blade with quadrantbrackets centered between blade ribs. Securewith three 3/4" x 4" clevis pins, washers and cotterpins.3. Center large shield end of one of the shockabsorbers with a 1/2" spacer on each sidebetween the blade ribs as shown in the diagram.Secure with 3/4" x 4" clevis pin, washer and cotterpin. Place other end between brackets indicatedon quadrant and secure with 3/4" x 3-1/4" clevispin, washer and cotter pin. The heads of the clevispins must be oriented as shown in the diagram.4. Repeat Step 3 for the second shock absorber.5. Thread one 5/8" nut halfway down on each of foureyebolts. Hook a spring to each of the quadrantbrackets indicated in the diagram. Hook an eyeboltto the other end of each trip spring.6. Push the threaded ends of the eyebolts throughthe four spring brackets on the blade. Install asecond nut on each eyebolt.CAUTIONOvertightening springs will not increase bladetrip force and can damage the springs.7. Tighten the top nuts until the coils of the tripsprings begin to separate (a piece of paper suchas this instruction sheet should pass between thesecond and third coils). Tighten the bottom nutagainst the spring brackets to lock in place.A-FRAME TO QUADRANT1. Place the A-frame nose plate over the quadrantpivot section. Secure with one 1" x 9" cap screw(pivot bolt), three fl at washers and a locknut asshown below. Tighten locknut as much as possiblewhile allowing A-frame and quadrant to pivot.QuadrantPivot Section1" x 9"Cap ScrewA-frameNose Plate1" Locknut1" FlatWashers2. Position the rod ends of the two 12" rams (foundin hydraulics box) in the brackets on the back ofthe quadrant. Secure the rod end of each ram tothe quadrant with a 1" x 3-1/4" clevis pin (installedfrom the top down through bracket), washer andcotter pin.3. Swing the A-frame to one side. Making surethe threaded port is facing away from theA-frame, position the base end of the ram intothe bracket on the side of the A-frame. Insert a1" x 3-1/4" clevis pin (installed from the bottomupward) and secure with a washer and cotter pin.4. Swing the A-frame to the other side and repeatStep 3 to connect the other ram to the A-frame.Lit. No. 66897, Rev. 07 7 June 15, 2010
Page 1: Western Products, PO Box 245038, Mi
Page 4 and 5: SAFETYSAFETY PRECAUTIONSImproper in
Page 8 and 9: INSTALLATION INSTRUCTIONSCHAIN TO A
Page 10 and 11: INSTALLATION INSTRUCTIONS4. Before
Page 12 and 13: INSTALLATION INSTRUCTIONSSTAND1. Po
Page 14 and 15: INSTALLATION INSTRUCTIONSLift RamTh
Page 16 and 17: INSTALLATION INSTRUCTIONS9. Install
Page 18 and 19: INSTALLATION INSTRUCTIONSPLOW BATTE
Page 20 and 21: OPERATIONAL TESTS AND FINAL ADJUSTM
Page 22 and 23: OPERATIONAL TESTS AND FINAL ADJUSTM
Page 24: Western ProductsPO Box 245038Milwau

II PRO PLUS Snowplow #64750/64999/66901/66974/66980

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?