PA50, 55 & 60 ECO MK2 - Operator Manual - McConnel

More documents

Recommendations

Info

ATTACHMENT TO TRACTORPosition the tractor squarely to the machineplacing the draft links at the same height asthe mainframe attachment points.Carefully reverse the tractor up to themachine until the draft links are positionedfor attachment – select the rear most holeon the machines lower link brackets thatallows the machine to be mounted withoutfouling the tractor.Attach the tractor draft links to the machineusing pins provided and secure in position -ensure the same mounting hole is selectedon each side of the machine.If necessary fit the spacers supplied tominimise sideways movement of the draftlinks within the hitch bracket12
Fit the stabilizer into position with its armsaligned with the holes of the main frameand attach the stabilizer nose to the tractorstop link – select the highest possibleposition available avoiding any loadsensing properties.NOTE: The bolt on nose of the stabiliser isreversible in order to accommodatevariations of tractor linkage designs.<strong>McConnel</strong> offer various versions ofstabilizer noses for differing types andmakes of tractors – contact your localdealer or <strong>McConnel</strong> Parts Department forfurther information.Secure the stabiliser in position using thefixings provided. Attach the stabiliser arm tothe machine selecting the lowest holepossible.Fit top link between the stabiliser and themainframes upper linkage point.13
Page 4 and 5: 2. REMEDIES AND PROCEDURES2.01. The
Page 6: POWER ARM INSPECTION AND MAINTENANC
Page 9 and 10: TRACTOR PRE-OPERATION InspectionPow
Page 11 and 12: TRACTOR PRE-OPERATION InspectionPow
Page 14 and 15: For Safety and Performance …ALWAY
Page 16: FEATURESPA50 Eco Models Linkage mou
Page 19 and 20: BEFORE USING THIS MACHINE YOU MUST:
Page 21 and 22: ADDITIONAL SAFETY ADVICETrainingOpe
Page 23 and 24: TRACTOR PREPARATIONFitting Tractor
Page 25: HYDRAULIC OILHydraulic Oil Reservoi
Page 29 and 30: Remove leg pins and raise the stand
Page 31 and 32: FITTING OPERATOR CONTROL UNITSFitme
Page 33 and 34: RUNNING UP PROCEDURECAUTION! Before
Page 35 and 36: REMOVAL FROM TRACTORDANGER!READ CAR
Page 37 and 38: CABLE CONTROLSCable controlled mach
Page 39 and 40: Rotor ControlRefer to specific cabl
Page 41 and 42: ELECTRIC SWITCHBOX CONTROLSMachines
Page 43 and 44: HEAD FLOAT OPERATION (Angle Float s
Page 45 and 46: ELECTRIC MONOLEVER CONTROLSMachines
Page 47 and 48: HEAD FLOAT OPERATION (Angle Float s
Page 49 and 50: XTC (Mk2) PROPORTIONAL SWITCHBOX CO
Page 51 and 52: HEAD FLOAT OPERATIONAngle Float (St
Page 53 and 54: V4 PROPORTIONAL CONTROLSPOWER ON /
Page 55 and 56: EDS FUNCTION (EDS Models) / LIFT FL
Page 57 and 58: SLEW - TELE / MIDCUT / VFR SWAPThis
Page 59 and 60: V4 JOYSTICK CONTROLS - Buttons & Th
Page 61 and 62: TELE / MIDCUT / VFR OPERATION - JOY
Page 63 and 64: V4 CONTROL UNIT - LED Screen Displa
Page 65 and 66: TEST & FAULT FINDING SCREENSThe fol
Page 67 and 68: BREAKAWAYThe machine is fitted with
Page 69 and 70: MOVING INTO TRANSPORT POSITIONSelec
Page 71 and 72: TRANSPORTING THE MACHINETransport H
Page 73 and 74: HAZARDS & DANGERSAdverse SlopesWhen
Page 75 and 76: Definitions of Exclusion ZonesRisk
Page 77 and 78:
LIFT FLOAT (Optional Extra for Grou
Page 79 and 80:
GENERAL MAINTENANCEGeneral Lubricat
Page 81 and 82:
HYDRAULIC SYSTEMOil SupplyCheck the
Page 83 and 84:
CONTROL CABLESThe control cables op
Page 85:
TORQUE SETTINGS FOR FASTENERSThe ch
show all

PA50, 55 & 60 ECO MK2 - Operator Manual - McConnel

Create successful ePaper yourself

Delete template?

Save as template?