to Download the One-Step Rust Converter MSDS - Auto Body ...

MATERIAL SAFETY DATA SHEET 3M(TM) Mar-Hyde(r) One-Step(r) Rust Converter, P.N. 3509 09/08/2008Material Safety Data SheetCopyright, 2008, 3M Company. All rights reserved. Copying and/or downloading of this information for the purpose of properlyutilizing 3M products is allowed provided that: (1) the information is copied in full with no changes unless prior written agreement isobtained from 3M, and (2) neither the copy nor the original is resold or otherwise distributed with the intention of earning a profitthereon.SECTION 1: PRODUCT AND COMPANY IDENTIFICATIONPRODUCT NAME: 3M(TM) Mar-Hyde(r) One-Step(r) Rust Converter, P.N. 3509MANUFACTURER: 3MDIVISION: Automotive AftermarketADDRESS: 3M CenterSt. Paul, MN 55144-1000EMERGENCY PHONE: 1-800-364-3577 or (651) 737-6501 (24 hours)Issue Date: 09/08/2008Supercedes Date: 04/30/2008Document Group: 24-9357-5Product Use:Intended Use:Specific Use:AutomotiveRust ConverterSECTION 2: INGREDIENTSIngredient C.A.S. No. % by WtDIMETHYL ETHER 115-10-6 15 - 40ACETONE 67-64-1 15 - 40METHYL ETHYL KETONE 78-93-3 10 - 30ACRYLIC POLYMER Trade Secret 5 - 10WATER 7732-18-5 1 - 52-BUTOXYETHANOL 111-76-2 1 - 5PROPRIETARY ADDITIVE Trade Secret 0.1 - 1SECTION 3: HAZARDS IDENTIFICATION3.1 EMERGENCY OVERVIEWSpecific Physical Form: AerosolOdor, Color, Grade: Solvent odor. Colorless.General Physical Form: LiquidImmediate health, physical, and environmental hazards: Flammable liquid and vapor. Flammable liquefied gas. Aerosolcontainer contains flammable gas under pressure. Closed containers exposed to heat from fire may build pressure and explode.Extremely flammable liquid and vapor. Vapors may travel long distances along the ground or floor to an ignition source and flash_________________________________________________________________________________________________Page 1 of 8

MATERIAL SAFETY DATA SHEET 3M(TM) Mar-Hyde(r) One-Step(r) Rust Converter, P.N. 3509 09/08/2008In the event of a release of this material, the user should determine if the release qualifies as reportable according tolocal, state, and federal regulations.SECTION 7: HANDLING AND STORAGE7.1 HANDLINGDo not eat, drink or smoke when using this product. Wash exposed areas thoroughly with soap and water. Keep away from heat,sparks, open flame, pilot lights and other sources of ignition. Ground containers securely when transferring contents. Wear low staticor properly grounded shoes. Do not pierce or burn container, even after use. Do not spray near flames or sources of ignition. Avoidbreathing of vapors, mists or spray. Avoid skin contact. Aerosol container contains flammable gas under pressure. Avoid staticdischarge. Avoid eye contact with vapors, mists, or spray. Avoid breathing of dust created by cutting, sanding, grinding ormachining. Avoid contact with oxidizing agents.7.2 STORAGEStore away from acids. Store away from heat. Store out of direct sunlight. Keep container tightly closed. Do not store containers ontheir sides. Store away from flammable and combustible materials. Store away from oxidizing agents. Store in a cool, dry place.SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION8.1 ENGINEERING CONTROLSUse in an enclosed process area is recommended. Provide appropriate local exhaust for cutting, grinding, sanding or machining. Donot use in a confined area or areas with little or no air movement. Local exhaust ventilation with a minimum capture velocity of 100linear feet per minute should be provided for applications at or above the boiling temperature. Use general dilution ventilation and/orlocal exhaust ventilation to control airborne exposures to below Occupational Exposure Limits and/or control mist, vapor, or spray. Ifventilation is not adequate, use respiratory protection equipment.8.2 PERSONAL PROTECTIVE EQUIPMENT (PPE)8.2.1 Eye/Face ProtectionAvoid eye contact with vapors, mists, or spray.The following eye protection(s) are recommended: Indirect Vented Goggles.8.2.2 Skin ProtectionAvoid skin contact.Select and use gloves and/or protective clothing to prevent skin contact based on the results of an exposure assessment. Consult withyour glove and/or protective clothing manufacturer for selection of appropriate compatible materials.Gloves made from the following material(s) are recommended: Butyl Rubber.8.2.3 Respiratory ProtectionAvoid breathing of vapors, mists or spray. Avoid breathing of dust created by cutting, sanding, grinding or machining.Select one of the following NIOSH approved respirators based on airborne concentration of contaminants and in accordance withOSHA regulations: Half facepiece or fullface air-purifying respirator with organic vapor cartridges and P95 particulate prefilters.Consult the current 3M Respiratory Selection Guide for additional information or call 1-800-243-4630 for 3M technical assistance.8.2.4 Prevention of SwallowingDo not eat, drink or smoke when using this product. Wash exposed areas thoroughly with soap and water.8.3 EXPOSURE GUIDELINESIngredient Authority Type Limit Additional Information_________________________________________________________________________________________________Page 4 of 8

MATERIAL SAFETY DATA SHEET 3M(TM) Mar-Hyde(r) One-Step(r) Rust Converter, P.N. 3509 09/08/20082-BUTOXYETHANOL ACGIH TWA 20 ppm Table A32-BUTOXYETHANOL OSHA TWA, Vacated 25 ppm Skin Notation*2-BUTOXYETHANOL OSHA TWA 50 ppm Skin Notation*; Table Z-1ACETONE ACGIH TWA 500 ppm Table A4ACETONE ACGIH STEL 750 ppm Table A4ACETONE OSHA TWA, Vacated 750 ppmACETONE OSHA TWA 1000 ppm Table Z-1ACETONE OSHA STEL, Vacated 1000 ppmDIMETHYL ETHER AIHA TWA 1000 ppmDIMETHYL ETHER CMRG TWA 1000 ppmMETHYL ETHYL KETONE ACGIH TWA 200 ppmMETHYL ETHYL KETONE ACGIH STEL 300 ppmMETHYL ETHYL KETONE OSHA TWA 200 ppm Table Z-1AMETHYL ETHYL KETONE OSHA STEL 300 ppm Table Z-1A* Substance(s) refer to the potential contribution to the overall exposure by the cutaneous route including mucous membrane and eye,either by airborne or, more particularly, by direct contact with the substance. Vehicles can alter skin absorption.VAC Vacated PEL:Vacated Permissible Exposure Limits [PEL] are enforced as the OSHA PEL in some states. Check with your localregulatory agency.SOURCE OF EXPOSURE LIMIT DATA:ACGIH: American Conference of Governmental Industrial HygienistsCMRG: Chemical Manufacturer Recommended GuidelineOSHA: Occupational Safety and Health AdministrationAIHA: American Industrial Hygiene Association Workplace Environmental Exposure Level (WEEL)SECTION 9: PHYSICAL AND CHEMICAL PROPERTIESSpecific Physical Form:AerosolOdor, Color, Grade:Solvent odor. Colorless.General Physical Form:LiquidAutoignition temperatureNo Data AvailableFlash Point-20 ºF [Test Method: Pensky-Martens Closed Cup]Flammable Limits - LEL 1.1 %Flammable Limits - UEL 27.0 %Boiling point -13 ºFDensity6.50 lb/galVapor Density> 1 [Ref Std: AIR=1]Vapor PressureSpecific GravitypHMelting pointSolubility in WaterHazardous Air PollutantsVolatile Organic CompoundsVolatile Organic CompoundsPercent volatileVOC Less H2O & Exempt SolventsNo Data Available0.78 [Ref Std: WATER=1]No Data AvailableNo Data AvailableComplete0.00 lb HAPS/gal50.9 % weight3.30 lb/gal91.1 % weight5.42 lb/galSECTION 10: STABILITY AND REACTIVITY_________________________________________________________________________________________________Page 5 of 8

MATERIAL SAFETY DATA SHEET 3M(TM) Mar-Hyde(r) One-Step(r) Rust Converter, P.N. 3509 09/08/2008Stability: Stable.Materials and Conditions to Avoid: Heat; Sparks and/or flames; Strong oxidizing agentsHazardous Polymerization: Hazardous polymerization will not occur.Hazardous Decomposition or By-ProductsSubstanceCarbon monoxideCarbon dioxideConditionDuring CombustionDuring CombustionSECTION 11: TOXICOLOGICAL INFORMATIONPlease contact the address listed on the first page of the MSDS for Toxicological Information on this material and/or itscomponents.SECTION 12: ECOLOGICAL INFORMATIONECOTOXICOLOGICAL INFORMATIONNot determined.CHEMICAL FATE INFORMATIONNot determined.SECTION 13: DISPOSAL CONSIDERATIONSWaste Disposal Method: Incinerate in a permitted hazardous waste incinerator. As a disposal alternative, dispose of waste productin a permitted hazardous waste facility.Facility must be capable of handling aerosol cans.EPA Hazardous Waste Number (RCRA): D001 (Ignitable), D035 (Methyl ethyl ketone)Since regulations vary, consult applicable regulations or authorities before disposal.SECTION 14:TRANSPORT INFORMATIONID Number(s):LB-K100-0553-4, 70-0080-0495-7_________________________________________________________________________________________________Page 6 of 8

MATERIAL SAFETY DATA SHEET 3M(TM) Mar-Hyde(r) One-Step(r) Rust Converter, P.N. 3509 09/08/2008Please contact the emergency numbers listed on the first page of the MSDS for Transportation Information for thismaterial.SECTION 15: REGULATORY INFORMATIONUS FEDERAL REGULATIONSContact 3M for more information.311/312 Hazard Categories:Fire Hazard - Yes Pressure Hazard - Yes Reactivity Hazard - No Immediate Hazard - Yes Delayed Hazard - YesSection 313 Toxic Chemicals subject to the reporting requirements of that section and 40 CFR part 372 (EPCRA):Ingredient C.A.S. No % by Wt2-BUTOXYETHANOL (GLYCOL ETHERS) 111-76-2 1 - 5STATE REGULATIONSContact 3M for more information.CHEMICAL INVENTORIESThe components of this product are in compliance with the chemical notification requirements of TSCA.Contact 3M for more information.INTERNATIONAL REGULATIONSContact 3M for more information.This MSDS has been prepared to meet the U.S. OSHA Hazard Communication Standard, 29 CFR 1910.1200.SECTION 16: OTHER INFORMATIONNFPA Hazard ClassificationHealth: 2 Flammability: 4Reactivity: 0 Special Hazards: NoneNational Fire Protection Association (NFPA) hazard ratings are designed for use by emergency response personnel to address the hazards that arepresented by short-term, acute exposure to a material under conditions of fire, spill, or similar emergencies. Hazard ratings are primarily based on theinherent physical and toxic properties of the material but also include the toxic properties of combustion or decomposition products that are known to_________________________________________________________________________________________________Page 7 of 8

MATERIAL SAFETY DATA SHEET 3M(TM) Mar-Hyde(r) One-Step(r) Rust Converter, P.N. 3509 09/08/2008be generated in significant quantities.Revision Changes:Section 1: Initial issue message was modified.DISCLAIMER: The information in this Material Safety Data Sheet (MSDS) is believed to be correct as of the date issued. 3MMAKES NO WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTYOF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF PERFORMANCE OR USAGE OFTRADE. User is responsible for determining whether the 3M product is fit for a particular purpose and suitable for user's method ofuse or application. Given the variety of factors that can affect the use and application of a 3M product, some of which are uniquelywithin the user's knowledge and control, it is essential that the user evaluate the 3M product to determine whether it is fit for aparticular purpose and suitable for user's method of use or application.3M provides information in electronic form as a service to its customers. Due to the remote possibility that electronic transfer mayhave resulted in errors, omissions or alterations in this information, 3M makes no representations as to its completeness or accuracy.In addition, information obtained from a database may not be as current as the information in the MSDS available directly from 3M.3M MSDSs are available at www.3M.com_________________________________________________________________________________________________Page 8 of 8