MIC-3358 User's Manual - ECA Services Ltd

More documents

Recommendations

Info

On-Chip Primary/Secondary PCI IDEThe integrated peripheral controller contains an IDE interface with supportfor two IDE channels. Select Enabled to activate each channel separately.The settings are: Enabled (Default) and Disabled.IDE Primary/Secondary Master/Slave PIOThe four IDE PIO (Programmed Input/Output) fields let you set a PIOmode (0-4) for each of the four IDE devices that the onboard IDE interfacesupports. Modes 0 through 4 provide successively increased performance.In Auto mode, the system automatically determines the best modefor each device. The settings are: Auto (Default), Mode 0, Mode 1, Mode2, Mode 3, Mode 4.IDE Primary/Secondary Master/Slave UDMAUltra DMA/33 implementation is possible only if your IDE hard drivesupports it and the operating environment includes a DMA driver (Windows95 OSR2 or a third-party IDE bus master driver). If your hard driveand your system software both support Ultra DMA/33 and Ultra DMA/66and Ultra DMA/100, select Auto to enable BIOS support. The settingsare: Auto (Default), Disabled.USB ControllerSelect Enabled if your system contains a Universal Serial Bus (USB) 1.1controller. The settings are: Enabled (Default), Disabled.USB 2.0 ControllerSelect Enabled if your system contains a Universal Serial Bus (USB) 1.1/2.0 controller. The settings are: Enabled (Default), Disabled.USB Keyboard/Mouse SupportSelect Enabled if you use USB KB/Mouse in DOS mode.Init Display FirstUser can choose display priority on either peripheral PCI slot or on boardVGA chip. There are 2 options: PCI slot (Default) and On board.MIC-3358 User’s Manual 58
SMBus ConnectorUsers can select IPMI source and application as below.SourcePCF8584THardware Monitor 83782DBMC (PMC type) (Reserved)connected CMMMIC-3924BMIC-3924ACMM (Reserved)There are 3 options: MIC-3924B (Default), MIC-3924A and CMM.LAN 1 ConnectorThe item allows you to choice LAN1 connective way. There are 3options: Front (Default), 2.16 and RearLAN 2 ConnectorThe item allows you to choice LAN2 connective way. There are 2options: 2.16 and Rear (Default)IDE HDD Block ModeBlock mode is also called block transfer, multiple commands, or multiplesector read/write. If your IDE hard drive supports block mode (most newdrives do), select Enabled for automatic detection of the optimal numberof block read/writes per sector the drive can support. The settings are:Enabled (Default), Disabled.Onboard FDC ControllerSelect Enabled if your system has a floppy disk controller (FDD)installed on the system board and you wish to use it. If you install add-onFDC or the system has no floppy drive, select Disabled in this field. Thesettings are: Enabled (Default) and Disabled.Onboard Serial Port 1/Port 2Select an address and corresponding interrupt for the first and secondserial ports. The Serial Port 1 settings are: 3F8/IRQ4 (Default), 2E8/IRQ3, 3E8/IRQ4, 2F8/ IRQ3, Disabled, Auto.59 Chapter 4
Page 1 and 2:
MIC-33586U CompactPCI Intel ®Penti
Page 3 and 4:
CE NotificationThe MIC-3358, develo
Page 5 and 6:
ContentsChapter 1 Hardware Configur
Page 7 and 8:
4.1.2 Standard CMOS Setup..........
Page 9 and 10:
CHAPTER1HardwareConfiguration
Page 11 and 12:
PMC (PCI Mezzanine Card) IEEE1386.1
Page 13 and 14:
• Display memory: 8MB SDRAM VRAM
Page 15 and 16: Table 1.2: JP1 jumper definition5V3
Page 17 and 18: Table 1.7: CN1 IDE Connector Defini
Page 19 and 20: Table 1.9: CN3 RJ-45 COM1 port Defi
Page 21 and 22: Table 1.11: CN5 USB 1.1/2.0 port De
Page 23 and 24: 3 MDIAX2+4 MDIAX3+5 MDIAX3-6 MDIAX2
Page 25 and 26: 41 +3.3V 42 SERR#43 C/BE1# 44 GND45
Page 27 and 28: It's automatic selection when SW1-1
Page 29 and 30: Figure 1.3: MIC-3358 jumpers and co
Page 31 and 32: 2. Disconnect power before making a
Page 33 and 34: CHAPTER2ConnectingPeripherals
Page 35 and 36: 2.4 Serial Ports (CN3 and Rear I/O)
Page 37 and 38: of MIC-3358 help you install and re
Page 39 and 40: CHAPTER3Driver Setup
Page 41 and 42: 3.3 CMM (Chassis Management Module)
Page 43 and 44: Figure 3.5: Select: Add a new devic
Page 45 and 46: Figure 3.9: Browse for driver on CD
Page 47 and 48: Figure 3.13: Click: NextFigure 3.14
Page 49 and 50: 3.3.2 Windows XP DriverFigure 3.17:
Page 51 and 52: Figure 3.21: Select: Add a new hard
Page 53 and 54: Figure 3.25: Select driver on CD-RO
Page 55 and 56: Figure 3.29: My computer: A-IPM dri
Page 57 and 58: CHAPTER4Award BIOS Setup
Page 59 and 60: 4.1.2 Standard CMOS SetupThe items
Page 61 and 62: First/Second/Third Boot Device and
Page 63 and 64: Small logo (EPA) showDefault is Dis
Page 65: Delayed TransactionThe chipset has
Page 69 and 70: ACPI FunctionThis category allows y
Page 71 and 72: Load Optimized Defaults (Y/N) ? NPr
Page 73 and 74: AppendixAWatchdog Timer
Page 75 and 76: 1070 RETURN2000 REM Subroutine #2,
Page 77 and 78: AppendixBPin Assignments
Page 79 and 80: B.2 J2 ConnectorTable B.2: J2 conne
Page 81 and 82: B.4 J5 ConnectorTable B.4: J5 conne
Page 83 and 84: 4000-40BF Motherboard resources5000
show all

MIC-3358 User's Manual - ECA Services Ltd

Create successful ePaper yourself

Delete template?

Save as template?