MIC-3358 User's Manual - ECA Services Ltd

More documents

Recommendations

Info

Appendix A Watchdog TimerA.1 Programming the Watchdog TimerTo program the watchdog timer, you must write a program which writes avalue to I/O port address 443 (hex). This output value represents timeinterval. The value range is from 01 (hex) to FF (hex), and the relatedtime interval is 1 sec. to 255 sec.Data Time Interval01 1 sec.02 2 sec.03 3 sec.04 4 sec.•••FF 255 sec.After data entry, your program must refresh the watchdog timer by rewritingthe I/O port 443. When you want to disable the watchdog timer, yourprogram should read I/O port 043 (hex). The following example showshow you might program the watchdog timer in BASIC:10 REM Watchdog timer example program20 OUT &H443, data REM Start and restart the watchdog30 GOSUB 1000 REM Your application task #1,40 OUT &H443, data REM Reset the timer50 GOSUB 2000 REM Your application task #2,60 OUT &H443, data REM Reset the timer70 X=INP (&H043) REM, Disable the watchdog timer80 END1000 REM Subroutine #1, your application task•••<strong>MIC</strong>-3369 User’s <strong>Manual</strong> 66
1070 RETURN2000 REM Subroutine #2, your application task•••2090 RETURN.67 Chapter A
Page 1 and 2:
MIC-33586U CompactPCI Intel ®Penti
Page 3 and 4:
CE NotificationThe MIC-3358, develo
Page 5 and 6:
ContentsChapter 1 Hardware Configur
Page 7 and 8:
4.1.2 Standard CMOS Setup..........
Page 9 and 10:
CHAPTER1HardwareConfiguration
Page 11 and 12:
PMC (PCI Mezzanine Card) IEEE1386.1
Page 13 and 14:
• Display memory: 8MB SDRAM VRAM
Page 15 and 16:
Table 1.2: JP1 jumper definition5V3
Page 17 and 18:
Table 1.7: CN1 IDE Connector Defini
Page 19 and 20:
Table 1.9: CN3 RJ-45 COM1 port Defi
Page 21 and 22:
Table 1.11: CN5 USB 1.1/2.0 port De
Page 23 and 24: 3 MDIAX2+4 MDIAX3+5 MDIAX3-6 MDIAX2
Page 25 and 26: 41 +3.3V 42 SERR#43 C/BE1# 44 GND45
Page 27 and 28: It's automatic selection when SW1-1
Page 29 and 30: Figure 1.3: MIC-3358 jumpers and co
Page 31 and 32: 2. Disconnect power before making a
Page 33 and 34: CHAPTER2ConnectingPeripherals
Page 35 and 36: 2.4 Serial Ports (CN3 and Rear I/O)
Page 37 and 38: of MIC-3358 help you install and re
Page 39 and 40: CHAPTER3Driver Setup
Page 41 and 42: 3.3 CMM (Chassis Management Module)
Page 43 and 44: Figure 3.5: Select: Add a new devic
Page 45 and 46: Figure 3.9: Browse for driver on CD
Page 47 and 48: Figure 3.13: Click: NextFigure 3.14
Page 49 and 50: 3.3.2 Windows XP DriverFigure 3.17:
Page 51 and 52: Figure 3.21: Select: Add a new hard
Page 53 and 54: Figure 3.25: Select driver on CD-RO
Page 55 and 56: Figure 3.29: My computer: A-IPM dri
Page 57 and 58: CHAPTER4Award BIOS Setup
Page 59 and 60: 4.1.2 Standard CMOS SetupThe items
Page 61 and 62: First/Second/Third Boot Device and
Page 63 and 64: Small logo (EPA) showDefault is Dis
Page 65 and 66: Delayed TransactionThe chipset has
Page 67 and 68: SMBus ConnectorUsers can select IPM
Page 69 and 70: ACPI FunctionThis category allows y
Page 71 and 72: Load Optimized Defaults (Y/N) ? NPr
Page 73: AppendixAWatchdog Timer
Page 77 and 78: AppendixBPin Assignments
Page 79 and 80: B.2 J2 ConnectorTable B.2: J2 conne
Page 81 and 82: B.4 J5 ConnectorTable B.4: J5 conne
Page 83 and 84: 4000-40BF Motherboard resources5000
show all

MIC-3358 User's Manual - ECA Services Ltd

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?