Specifications for a Quality Label for Paint, Lacquer and ... - Qualicoat

More documents

Recommendations

Info

5.1.6 Examination of registersThe inspector must check that the coating plant maintains registers according tosection 3.9.In the in-house control register he will check that the results recorded in the registercoincide with the results of the test panels. The results recorded in the register coincidewith the results of the test panels. For this reason, all test panels must be kept and heldat the inspector’s disposal for one year.5.1.7 Final assessment for granting the licenceThe inspector submits the inspection report to the general licensee.The inspection reports are assessed by the general licensee. Under the supervision ofQUALICOAT, the general licensee decides whether or not to grant a licence.- If the results of both inspections meet the requirements, a licence to use the qualitylabel will be granted.- If the results of one of the two inspections do not meet the requirements, the coater willbe informed that the licence to use the quality label cannot be granted for the timebeing, stating all details and reasons. The coater must wait three months beforemaking a new application for a licence to use the quality label.5.2. Routine inspections of licenseesAfter a plant has been granted a licence to use the quality label, it will be inspected at leasttwice but no more than five times a year. Routine inspections must be made without priornotice and must include:- Inspection of laboratory equipment as described in 3.5.- Inspection of pre-treatment as described in 3.2 or 3.3.- Inspection of finished products as described in 5.1.4 and inspection of test panels asspecified in 5.1.5.- An acetic acid salt spray test to be carried out at least once a year.- A check of the registers according to 5.1.6.- The coating plant must check the accuracy of the oven's temperature indicator or haveit checked at least twice a year. The results of this check are to be entered in a specialregister which is to be presented to the inspector when he makes the routineinspections.The inspector submits the inspection report to the general licensee.The inspection reports are assessed by the general licensee. Under the supervision ofQUALICOAT, the general licensee decides whether to renew or withdraw the licence.- If the results of the inspection meet the requirements, authorisation to use the qualitylabel will continue.- If the results of the inspection do not meet the requirements, another inspection mustbe made within one month (allowing for holiday periods).QUALICOAT SPECIFICATIONS 31 11 th Edition
- If the second inspection again produces unsatisfactory results, the licence to use thequality label will be withdrawn immediately. The coating plant must wait at least threemonths before making a new application for a licence to use the quality label.5.3. Use of the logo by coatersThe use of the logo must comply with the Regulations for use of the QUALICOATquality label (Appendix A1).QUALICOAT SPECIFICATIONS 32 11 th Edition
Page 1: SPECIFICATIONSFOR A QUALITY LABELFO
Page 7 and 8: TERMINOLOGYLicence:Approval:General
Page 9 and 10: 2. Test Methods and RequirementsThe
Page 11 and 12: Rating:This sample is good because
Page 13 and 14: 2.8. Impact test(for powder coating
Page 15 and 16: 2.12. Accelerated weathering testEN
Page 17 and 18: For powder coatings, this test is o
Page 19 and 20: Chapter 3Work SpecificationsQUALICO
Page 22 and 23: - Before application, each coating
Page 24 and 25: Chapter 4Approval of CoatingsQUALIC
Page 26 and 27: 7) Impact test (2.8)8) Resistance t
Page 28 and 29: 4.3. Use of the logo by coating man
Page 30 and 31: 5. Licensing of Coating PlantsThis
Page 34 and 35: Chapter 6Specifications for In-Hous
Page 36 and 37: 6.1.4 Measuring the drying temperat
Page 38 and 39: 6.3.4 Adhesion test (EN ISO 2409)Th
Page 40: 6.4.3 Control register for finished
Page 43 and 44: AppendicesAppendicesA1 - Regulation
Page 45 and 46: Appendices5.3 Use of the logo by su
Page 47 and 48: AppendicesA2 - Specifications for D
Page 49 and 50: Appendices• Light fastness testTh
Page 51 and 52: AppendicesCheck-list for in-house c
Page 53 and 54: Appendicesthe GL's instructions, ke
Page 55 and 56: Appendices5. APPEARANCE OF THE FINA
Page 57 and 58: AppendicesA5 - Special specificatio
Page 59 and 60: AppendicesA6 - Procedure for evalua
Page 61 and 62: Appendicesg) Coating to be appliedQ
Page 63 and 64: Appendices5. RESPONSIBILITYa) Suppl
Page 65 and 66: AppendicesA8 - Specifications for b
Page 67: AppendicesNº YEAR TITLE SPECIFICAT

Specifications for a Quality Label for Paint, Lacquer and ... - Qualicoat

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?