Specifications for a Quality Label for Paint, Lacquer and ... - Qualicoat

More documents

Recommendations

Info

Chapter 6Specifications for In-House ControlQUALICOAT SPECIFICATIONS - 33 - 11 th Edition
6. Specifications for In-House Control6.1. Testing the parameters6.1.1 Pre-treatment bathsThe chemical elements defined by the supplier of the pre-treatment products must beanalysed at least:once a day (24 hours) per bath.The coater must increase the frequency of the analyses of his own accord if it provesnecessary on account of the analyses made.The results of these analyses must be entered in charts or some other record (register)readily accessible to the inspector. They must show the nominal values, maximumvalues not to be exceeded, actual values recorded and the number of shifts worked. Aseparate record must be kept for each bath.If necessary, any corrective measures must be noted on the chart opposite the date ofthe analysis. If not, they must be recorded in the register.6.1.2 Water QualityThe conductivity of the final rinsing preceding chromate bath and of the demineralisedrinsing water must be measured at least:once a day (24 hours)The coater must increase the frequency of the analyses of his own accord if it provesnecessary on account of the analyses made.The results of these analyses must be entered in charts or some other record (register)readily accessible to the inspector. They must show the nominal values, maximumvalues not to be exceeded, actual values recorded and the number of shifts worked.6.1.3 Measuring the temperature of pre-treatment and rinsing bathsThe temperature of the pre-treatment baths and the final rinse, if a hot water rinse,must be measured at least:once a day (24 hours) per bathThe results of these measurements must be entered in charts or some other record(register) readily accessible to the inspector. They must show the nominal values,maximum values not to be exceeded, actual values recorded and the number of shiftsworked.QUALICOAT SPECIFICATIONS - 34 - 11 th Edition
Page 1: SPECIFICATIONSFOR A QUALITY LABELFO
Page 7 and 8: TERMINOLOGYLicence:Approval:General
Page 9 and 10: 2. Test Methods and RequirementsThe
Page 11 and 12: Rating:This sample is good because
Page 13 and 14: 2.8. Impact test(for powder coating
Page 15 and 16: 2.12. Accelerated weathering testEN
Page 17 and 18: For powder coatings, this test is o
Page 19 and 20: Chapter 3Work SpecificationsQUALICO
Page 22 and 23: - Before application, each coating
Page 24 and 25: Chapter 4Approval of CoatingsQUALIC
Page 26 and 27: 7) Impact test (2.8)8) Resistance t
Page 28 and 29: 4.3. Use of the logo by coating man
Page 30 and 31: 5. Licensing of Coating PlantsThis
Page 32 and 33: 5.1.6 Examination of registersThe i
Page 36 and 37: 6.1.4 Measuring the drying temperat
Page 38 and 39: 6.3.4 Adhesion test (EN ISO 2409)Th
Page 40: 6.4.3 Control register for finished
Page 43 and 44: AppendicesAppendicesA1 - Regulation
Page 45 and 46: Appendices5.3 Use of the logo by su
Page 47 and 48: AppendicesA2 - Specifications for D
Page 49 and 50: Appendices• Light fastness testTh
Page 51 and 52: AppendicesCheck-list for in-house c
Page 53 and 54: Appendicesthe GL's instructions, ke
Page 55 and 56: Appendices5. APPEARANCE OF THE FINA
Page 57 and 58: AppendicesA5 - Special specificatio
Page 59 and 60: AppendicesA6 - Procedure for evalua
Page 61 and 62: Appendicesg) Coating to be appliedQ
Page 63 and 64: Appendices5. RESPONSIBILITYa) Suppl
Page 65 and 66: AppendicesA8 - Specifications for b
Page 67: AppendicesNº YEAR TITLE SPECIFICAT

Specifications for a Quality Label for Paint, Lacquer and ... - Qualicoat

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?