Specifications for a Quality Label for Paint, Lacquer and ... - Qualicoat

More documents

Recommendations

Info

Appendices2.4 Renewal of the QUALIDECO licence2.4.1 Laboratory testsIn order for a licence to be renewed, two decorations selected either by the General Licensee orby QUALICOAT will be tested every year.The tests are the same as for the granting of the QUALIDECO licence.If the results of one test for one decoration do not meet the requirements, the test must berepeated.2.4.2 InspectionIf the results of the test are again unsatisfactory, the decoration is not valid.After a plant has been granted a QUALIDECO licence, it will be inspected once a year accordingto § 2.3.2.The business records must also be examined in order to check that the QUALIDECOlicence is only used for approved decorations.The inspector submits the inspection report to the general licensee.The inspection reports are assessed by the general licensee. Under the supervision ofQUALICOAT, the general licensee decides whether to renew or withdraw the QUALIDECOlicence.• If the results of the inspection meet the requirements, the QUALIDECO licence will berenewed.• If the results of the inspection do not meet the requirements, another inspection must bemade within one month (allowing for holiday periods).• If the second inspection again produces unsatisfactory results, the QUALIDECO licencewill be withdrawn immediately. The decorator must wait at least three months beforemaking a new application for a QUALIDECO licence.3. Test reportAn official test report can be obtained from the national association or directly from theQUALICOAT Secretariat.4. Check-list for in-house controlSee following page11 th Edition - 49 - APPENDIX 2
AppendicesCheck-list for in-house controlDateReferenceCoaterCustomerQUALICOATapprovalbaseDecorationcodePaper codeProcessProductOven Before decoration After decorationDay Week Thickness Gloss AppearanceNotes11 th Edition - 50 - APPENDIX 2
Page 1: SPECIFICATIONSFOR A QUALITY LABELFO
Page 7 and 8: TERMINOLOGYLicence:Approval:General
Page 9 and 10: 2. Test Methods and RequirementsThe
Page 11 and 12: Rating:This sample is good because
Page 13 and 14: 2.8. Impact test(for powder coating
Page 15 and 16: 2.12. Accelerated weathering testEN
Page 17 and 18: For powder coatings, this test is o
Page 19 and 20: Chapter 3Work SpecificationsQUALICO
Page 22 and 23: - Before application, each coating
Page 24 and 25: Chapter 4Approval of CoatingsQUALIC
Page 26 and 27: 7) Impact test (2.8)8) Resistance t
Page 28 and 29: 4.3. Use of the logo by coating man
Page 30 and 31: 5. Licensing of Coating PlantsThis
Page 32 and 33: 5.1.6 Examination of registersThe i
Page 34 and 35: Chapter 6Specifications for In-Hous
Page 36 and 37: 6.1.4 Measuring the drying temperat
Page 38 and 39: 6.3.4 Adhesion test (EN ISO 2409)Th
Page 40: 6.4.3 Control register for finished
Page 43 and 44: AppendicesAppendicesA1 - Regulation
Page 45 and 46: Appendices5.3 Use of the logo by su
Page 47 and 48: AppendicesA2 - Specifications for D
Page 49: Appendices• Light fastness testTh
Page 53 and 54: Appendicesthe GL's instructions, ke
Page 55 and 56: Appendices5. APPEARANCE OF THE FINA
Page 57 and 58: AppendicesA5 - Special specificatio
Page 59 and 60: AppendicesA6 - Procedure for evalua
Page 61 and 62: Appendicesg) Coating to be appliedQ
Page 63 and 64: Appendices5. RESPONSIBILITYa) Suppl
Page 65 and 66: AppendicesA8 - Specifications for b
Page 67: AppendicesNº YEAR TITLE SPECIFICAT

Specifications for a Quality Label for Paint, Lacquer and ... - Qualicoat

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?