Ranco Eco-Cool E71R/E72R Temperature and ... - icemeister.net

More documents

Recommendations

Info

4.1.1 Wiring the controllerWARNING: Before wiring the controller, make sure that the refrigeration unit, fan, heater, and controller are not connected to the electrical supply.Do not apply voltage to the digital input.WARNING: If the compressor and a fan are connected to the same relay on the controller, the total current drawn by the compressor and fan mustnot exceed the value shown in section 8.4 Terminations.Use insulated spade connectors to connect the controller to the output loads. If your line voltage uses a neutral line and a phase line, connect the phase lineto the phase terminal(s) on the controller. Line 1 and Line 2 connections on the controller are not phase dependent. Connect the control sensor, optionalevaporator sensor, and optional defrost termination switch using the screw terminal block.E71RWiring ExampleE71R with Control Sensor and Optional Evaporator SensorDRAFT VERSIONE72RWiring ExampleE72R With Control Sensor, Optional Evaporator Sensor, Defrost Heater, and Defrost FanType E7 EcoCool Electronic Temperature and Defrost Controllers©2008 Invensys Controls All rights reserved.6
4.2 Mounting the displayED1The optional display can be flush mounted in a panel cutout up to 30ft (10m) from the controller. To mount the display flush to the panel, cut a 2.32” by 1”(64mm x 31mm) hole in the panel. Insert the display from the outside of the panel. Friction tabs on the sides of the display hold it in place.DRAFT VERSIONDisplayMountingCut-out1”(25.4 mm)2.32” (58.9 mm)4.3 Wiring the displayUse the Interface Box, Copy Card, and Display TTL Connector on the controller to connect to the display.5 FUNCTIONS AND FEATURES5.1.1 User controlThe adjustment knob can be rotated to select any control temperature within the configured range.The OFF and ON positions of the adjustment knob can be set to specific angles relative to full counter clockwise. Rotating the adjustment knob fully counterclockwise (to OFF) powers off the controller and compressor immediately. However, hazardous voltage remains. The controller, compressor, defrost heater,and defrost fan must be disconnected, prior to service, using a separate switch. If the On/Off Function is enabled and the knob is in the OFF position, rotatingthe knob clockwise powers on the controller.5.1.2 Control modeThe controller cycles the compressor or refrigeration solenoid valve to maintain the selected control temperature.DifferentialsThe warm and cold adjustment knob positions are configured using four setpoints. Cut-In Warm and Cut-Out Warm are the setpoints for the warm position.Cut-In Cold and Cut-Out Cold are the setpoints for the cold position. The cold position is full clockwise rotation. The warm position is full counter clockwiserotation or, if the On/Off Function is enabled, the specified angle. When the user sets the adjustment knob to a setpoint between the warm and coldpositions, the Cut-In and Cut-Out setpoints are calculated by the controller. The setpoints can be configured using Celsius or Fahrenheit units.Cut-In Warm SetpointCut-Out Warm SetpointUser selectedCut-In and Cut-Out SetpointsTemperatureCut-InCut-OutKnob PositionCut-In Cold SetpointCut-Out Cold SetpointWarm PositionOFFUser SelectedPositionCold PositionType E7 EcoCool Electronic Temperature and Defrost Controllers©2008 Invensys Controls All rights reserved.7
Page 1 and 2: DRAFT VERSIONTemperature andDefrost
Page 3 and 4: and opening configuration files . .
Page 5: Optional DisplayTo minimize tempera
Page 9 and 10: DRAFT VERSIONTypicalCompressorCycle
Page 11 and 12: The E71R controller allows only off
Page 13 and 14: 5.1.6 DisplayThe optional display h
Page 15 and 16: DRAFT VERSION6.2 EcoCool configurat
Page 17 and 18: DRAFT VERSIONOn/Off FunctionSelect
Page 19 and 20: DRAFT VERSIONDefrost DurationSpecif
Page 21 and 22: DRAFT VERSIONCompressor Minimum Off
Page 23 and 24: DRAFT VERSION6.2.5.8 FanUse the Fan
Page 25 and 26: DRAFT VERSION6.2.8 Transferring fir
Page 27 and 28: DRAFT VERSION6.3.2 Downloading a co
Page 29 and 30: Tab Ref Parameter Description Defau
Page 31 and 32: DRAFT VERSION8 TECHNICAL SPECIFICAT

Ranco Eco-Cool E71R/E72R Temperature and ... - icemeister.net

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?