Visualiner Series - Snap-on Equipment

More documents

Recommendations

Info

3e-iii. Specification selection method -- thisoption determines the format of the vehicle specificationselection. The standard format,the default, uses the vehiclemanufacturer as a startingpoint for spec selection.3e-iv. Printout type -- there are several differentprintout format styles that are available, depending onpreference dictated by certainlocations in the world. By default,the "Standard" printout typeis enabled, with optional Northernor Southern European formats.3e-v. All readings display position -- there arethree different alignment readings screens during thesoftware path -- Front, Rear,and All Readings (front & rearon the same screen). This selectionallows the operator toestablish when the All Readingsscreen will appear, eitherfirst before the front & rear meterscreens or last after the meterscreens.Page 36
4. LanguageA variety of different languagesare available for the <strong>Visualiner</strong><strong>Series</strong> CD-ROM software models.Place the highlight boxaround Language on the SetupMenu and press Enter.The Language and SpecMenu gives the following submenuselections:Screen language -- choose the language on-screentext will be displayed.Printer language -- choose the language for customerprintouts.Vehicle spec selection -- choose the vehicle specificationdatabase for the country the aligner is used.4a. Language Selection -- To change the languagedisplayed on the screen or printout, select the item onthe Language and Spec Menu. Press the up/downarrow keys until the desired language is encircled bythe highlight bar and press Enter. Notice the "scrollbar" on the right side of the screen, indicating additionalchoices are available on a second page. Usethe arrow keys or "Page Forward" key to move to pagetwo. All screens will now be in the chosen language.English is the first selection on the list, should itbecome necessary to change the unit back to thedefault setting. For Asian aligners, Chinese will bethe first language listed. On floppy software units,only two of the listed languages are available.4b. Vehicle spec selection -- the <strong>Visualiner</strong> CD-ROM software contains wheel alignment specificationsfor the vehicles from many countries and markets.This setup option allows for changing the specdatabase to suit the country where the <strong>Visualiner</strong> isoperated.Note: some automotive markets not specificallyidentified on this screen have vehicles from a varietyof sources. It may be necessary to change databasesin order to locate specifications on somevehicles.Page 37
Page 1 and 2: Visualiner <strong
Page 3 and 4: ®309 Exchange AvenueConway, AR 720
Page 5 and 6: SAFETY INFORMATIONFor your safety,
Page 7 and 8: Risk of entanglement or crushing. T
Page 9 and 10: Table of ContentsPage1. Getting Sta
Page 11 and 12: IntroductionThis manual is designed
Page 13 and 14: TMVisualiner <stro
Page 15 and 16: IntroductionThis section is designe
Page 17 and 18: Getting StartedThe Visualin
Page 19 and 20: Computer ConnectionsInstallation of
Page 21 and 22: Wheel ClampsThe wheel clamps allow
Page 23 and 24: The Visualiner <st
Page 27 and 28: SetupMenuRack/FloorSystemConfigurat
Page 29 and 30: 2a. Heads -- choose the measuring h
Page 31 and 32: 2e. Software Configuration Menu --
Page 33 and 34: 3c-ii. Colors Selection -- the choi
Page 35: 3e. Optional Alignment Styles -- ad
Page 39 and 40: 5b. Angle Units Selection -- move t
Page 41 and 42: (Blank Page)
Page 45 and 46: IntroductionThe Visualiner<
Page 47 and 48: Steps To Performing A Quality 4 Whe
Page 49 and 50: ○ ○ ○ ○ ○ ○ ○ ○ ○
Page 51 and 52: ○ ○ ○ ○ ○ ○ ○ ○ ○
Page 53 and 54: Performing a Wheel Alignment ... co
Page 59 and 60: ○ ○ ○ ○ ○ ○ ○ ○ ○
Page 67 and 68: Measuring Other AnglesMeasuring Ste
Page 69 and 70: ○ ○ ○ ○ ○ ○ ○ ○ ○
Page 71 and 72: Adjustment AssistantAdjustment Assi
Page 73 and 74: Adjustment Assistant ... continuedT
Page 75 and 76: Adjustment Assistant ... continuedC
Page 77 and 78: Other Soft-Key FeaturesDriver Compl
Page 79: Other Soft-Key FeaturesTreadwear --
Page 82 and 83: Glossary of Alignment Terms* Indivi
Page 84 and 85: (Blank Page)
Page 86 and 87:
(Blank Page)
Page 88 and 89:
Customer Files MenuFrom the Files M
Page 90 and 91:
Using Database During an AlignmentA
Page 92 and 93:
Saving Complete AlignmentsAs noted
Page 94 and 95:
(Blank Page)
Page 96 and 97:
(Blank Page)
Page 98 and 99:
(Blank Page)
Page 100 and 101:
Customer Calibration ... continuedS
Page 102 and 103:
Customer Calibration ... continuedB
Page 104 and 105:
Measurement Data DisplayThese scree
Page 106 and 107:
User Serviceable PartsMany parts of
Page 108 and 109:
Troubleshooting Operational Problem
Page 110 and 111:
(Blank Page)
Page 112:
TMUSAJohn Bean Company309 Exchange
show all

Visualiner Series - Snap-on Equipment

Create successful ePaper yourself

Delete template?

Save as template?