Socket Sets

9Pliers and SnipsRetaining Ring PliersRetaining Ring Pliers Selection GuideNote: Always select the largest diameter tip that will fit the retaining ring. To obtain correct pliers or retaining ring number, measure diameter ofshaft (external) or bore (internal) where ring is to be installed or removed, and refer to table below. Retaining ring dash numbers are expressedin hundredths of an inch. Example: 5101-75 identifies Truarc’s external ring series 5101 for a shaft approximately 0.750" (3/4") O.D.Retaining Ring Manufacturers Cross ReferenceEXTERNALINTERNALTip Tip Product For Retaining Rings by following manutacturers For Retaining Rings by following manutacturersDia., AngleIn Int./Ext. Shaft Dia., Anderton Dash Bore Dia., Anderton DashExternal Internal Convertible Inches United Industro Truarc Number Inches United Industro Truarc Number0° 67-917 67-965 — 1400 3100 5100 N1300 3000X N5000.025 45° — — —3/16 to 15/64 140114023101 51015102-18 thru -23 1/4 to 5/16 N1301N13023001X N5001N5002-25 thru -3190° — — —5/8 1308 4000 5008 -620° 67-923 67-971 68-025 1/4 to 21/32 1400 3100 5100.038 45° — 67-973 68-026140114023101 51015102-25 thru -66 3/8 to 9/16 N1300N13013000X3001XN5000N5001 -37 thru -5690° 67-927 — 68-027 1/2 to 1 1408 4100 5108 -50 thru -100 1 to 1.02 N1302 N5002 -100 thru -1021/8 to 5/32 1440 5555 -12 thru -15 3/4 to 1 1308 4000 5008 -75 thru -1000° — — 68-028 11/16 to 7/8 1400 3100 5100 -68 thru -87 5/8 to 1.02 N1300 3000X N5000.047 45° — — 68-0291401 3101 5101 N1301 3001X N5001 -62 thru -10213/16 to 1 1408 4100 5108 -81 thru -100 1 to 1.02 N1302 N5002 -100 thru -10290° — — 68-030 3/16 to 1/4 1440 5555 -18 thru -25 1-1/16 to 1-3/8 1308 4000 5008 -106 thru -1370° 67-929 67-977 68-031 15/16 to 1-7/16 1400 3100 5100 -93 thru -143 1-1/16 to 1-3/4 N1300 3000X N5000.070 45° — — 68-0321 to 1-7/16140114023101 51015102 -100 thru -143N1301N13023001X N5001N5002-106 thru -17590° — — 68-033 1-1/16 to 2 1408 4100 5108 -106 thru -2005/16 to 5/8 1440 5555 -31 thru -621-7/16 to 2 1308 4000 5008 -143 thru -2000° — 67-983 68-034 1-1/2 to 3-1/2 1401 3100 5100 -150 thru -350 1-3/16 to 3 N1300 3000X N5000 -181 thru -300.090 45° — — 68-0351402 5102 N1302 3001X N50021-1/2 to 1-3/4 1401 3101 5101 -150 thru -17590° — — 68-0362-1/16 to 3 1308 4000 5008 -206 thru -3002-5/32 to 3-11/32 1408 4101 5108 -215 thru -3340° 67-935 — — 1400 3100 5100.115 45° — — —1-1/2 to 3-1/2 140114023101 51015102-150 thru -35090° — — —2-1/8 to 3-11/32 1408 4100 5108 -215 thru -334Set 68-04012 Pc. Internal/External Retaining Ring Plier SetFurnished in blow-molded plastic case. Includes retaining ring chart andspaces for storing rings.Approximate Weight, 3.50 lbs.ProductNumber Description68-025 .038 Tip, Internal/External, Straight68-026 .038 Tip, Internal/External, 45°68-027 .038 Tip, Internal/External, 90°68-028 .047 Tip, Internal/External, Straight68-029 .047 Tip, Internal/External, 45°68-030 .047 Tip, Internal/External, 90°68-031 .070 Tip, Internal/External, Straight68-032 .070 Tip, Internal/External, 45°68-033 .070 Tip, Internal/External, 90°68-034 .090 Tip, Internal/External, Straight68-035 .090 Tip, Internal/External, 45°68-036 .090 Tip, Internal/External, 90°9-11Always wear eye protection when near tools in use.