IOM - Johnson Controls Inc.

More documents

Recommendations

Info

FORM 145.19-IOM1 (908)VPH UNIT DIMENSIONSUnit Model A B C D009 ,012, 018, 024 20 20 12.38 14.88030 & 036 24 25 12.38 17.38LD13519Fig. 2 - 3/4 to 3 Ton VPH-B Dimensions & Connection locations8JOHNSON CONTROLS
FORM 145.19-IOM1 (908)6. CLEARANCESThe unit is design certified for closet installation withthe minimum clearances to combustible materialsas stated on the data label. No clearance is requiredfrom the top, sides, or back of the unit. A minimumof 1 inch clearance is required from the front to anycombustible materials. A combustible door may beplaced 6 inches from the front of the unit. When thedoor is open there must be 30 inches clearance toany obstruction, to allow sufficient access for serviceand the replacement of parts.8. WALL SLEEVEA factory-made wall sleeve is required to finishthe wall opening. The sleeve should be positionedwith a minimum of ¼” protruding from the finishedoutside wall face. This projection allows installationof the exterior grille without interference from theexterior finishing materials, and provides a rightangle surface to apply a caulking bead around thewall penetration.Use a spirit level or plumb line to make sure that thewall sleeve vertical flanges, which must mate withthe back of the unit, are perfectly vertical. The sleevemust be secured to the building framing with suitablefield-supplied fasteners (i.e. lag screws).Use shims as necessary, between thesleeve and the rough wall opening, tocompensate for any irregularities atthe sleeve fastening locations. DO NOTallow the fasteners to distort the wallsleeve side panels.CLOSETCLEARANCEDIMENSIONS(Inches)WALL SLEEVETHICKNESS009 - 024UNITS030 & 036UNITS"A" "D" "A" "D"5"- 8" 22 29 -"B" 27 33 -"B"8"- 12" 22 33 -"B" 27 37 -"B"12"- 15" 22 36 -"B" 27 40 -"B"A roll of ¾” wide x ½” thick self adhesive foam gasketis packed in the blower compartment of the unit, tobe used for sealing between the wall sleeve and theunit. Before moving the unit into final position, applyself-adhesive foam gasket to all the mating flangeson the wall sleeve, be sure to apply gasket materialto the divider panel flange between the top and bottomsections of the wall sleeve. Also apply gasketmaterial to the vertical flange of fresh air divider.LD135207. WALL OPENINGA finished opening in an outside wall is required forintake and exhaust of outdoor airflow. The rough-inopening dimensions required are as follows:□ 009 thru 024 Models = 21-3/4” wide by 44” high□ 030 and 036 Models = 26-3/4” wide by 44” highThe bottom edge of wall opening mustbe located at least 6” higher from finishedfloor.Consult local ordinances for framing requirements ofopenings through exterior structural walls.Johnson Controls9
Page 1 and 2: Single Package VerticalR-410A A/C &
Page 3 and 4: FORM 145.19-IOM1 (908)Changeability
Page 5 and 6: FORM 145.19-IOM1 (908)VPC & VPP UNI
Page 7: FORM 145.19-IOM1 (908)VPC/VPP UNIT
Page 11 and 12: FORM 145.19-IOM1 (908)9. EXTERIOR G
Page 13 and 14: FORM 145.19-IOM1 (908)14. AIR FILTE
Page 15 and 16: FORM 145.19-IOM1 (908)18. SEQUENCE
Page 17 and 18: FORM 145.19-IOM1 (908)Installed sys
Page 19 and 20: FORM 145.19-IOM1 (908)LD13527Johnso
Page 21 and 22: FORM 145.19-IOM1 (908)NOTESJohnson
Page 23 and 24: FORM 145.19-IOM1 (908)LIMITED WARRA

IOM - Johnson Controls Inc.

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?