English - Yamaha-Racingparts.com

More documents

Recommendations

Info

19. Spring Front ForkParts ListNo. PART No. PART NAME Q’TY REMARKS1 14B-23141-70 SPRG., Fr. FORK 1 11.0 N/mmIdentifying slits 32 14B-23141-75 SPRG., Fr. FORK 1 10.5 N/mmIdentifying slits 23 14B-23141-80 SPRG., Fr. FORK 1 10.0 N/mmIdentifying slits None4 14B-23141-85 SPRG., Fr. FORK 1 9.5N/mmIdentifying slits 1• There are slits at the ends of the spring for rateidentification.• The number of slits indicates the rate as shownabove.• When using an optional spring for the STD fork,replace the supplied preload tube with the set.NOTICEWhen using an optional spring for the kit fork, you do not need to replace the preloadtube. Use the original tube fitted to the fork.TIP• A spanner (SPECIAL TOOLS) and rod (SPECIAL TOOLS) are supplied with the front fork(14B-23102-70).• Use <strong>Yamaha</strong> M1 suspension oil.– 35 –
Front Fork Spring Replacement Method1. Turn the damping adjustor and preload adjustor anticlockwise to set to the weakestposition.2. After fixing the axle bracket in a vice, turn the fork bolt anticlockwise to lower the outer tubeuntil the dust seal touches the upper surface of the axle bracket.Rebound damping adjustorPreload adjustorFork boltAxle bracket3. Insert the spanner (SPECIAL TOOLS) into the notch of the spring seat upper and clamp the14mm special nut.4. Use a 14mm box spanner on the preload adjustor to remove the cap bolt assembly.NOTICEDo not remove the spanner (SPECIAL TOOLS) while doing this.Spanner(SPECIAL TOOLS)Spring seat upperPreload tube– 36 –
Page 1: ’09 YZF-R1KIT MANUALThe Performan
Page 4 and 5: 1 Engine SpecificationsSpec SB STDi
Page 6 and 7: 2. Spark Plug Set (14B-R465B-70)Par
Page 8 and 9: 4. High-lift CamshaftsParts ListNo.
Page 10 and 11: 6. Air Funnel Set (MGC-021008-00)Pa
Page 12 and 13: 6. Installing the Shaft AssemblyIns
Page 14 and 15: 7. Throttle Body Clamp Set (14B-135
Page 16 and 17: STD3KIT112- 13 -
Page 18 and 19: 10. Slipper Clutch Setting Set (4C8
Page 20 and 21: When installing the kit parts, the
Page 22 and 23: Parts ListNo. PART No. PART NAME Q'
Page 24 and 25: YZF-R1 Mission ratioGEARPLAN Ratio
Page 26 and 27: 12. Mission Maintenance Set (14B-A7
Page 28 and 29: Transmission AssemblyThe seal side
Page 30 and 31: 14. Sprocket Nut Set (4C8-A7463-70)
Page 32 and 33: 7865CrankcaseCrankcase322E/G2411-N-
Page 34 and 35: Rebound Damping Adjustment MethodTu
Page 36 and 37: 18. Front Fork ASSYParts ListNo. PA
Page 40 and 41: 5. Remove the push rod and fit the
Page 42 and 43: 20. Seat Cushion (13S-24713-70)Part
Page 44 and 45: 22. Rear Spare Wheel ASS’Y (4C8-2
Page 46 and 47: 14124Release side(White)Pull side(B
Page 48 and 49: 974Pull side(Black)5Release side(Wh
Page 50 and 51: 2-3 Installing Electrical Parts26.
Page 52 and 53: Diagnosis Functions• Use of the E
Page 54 and 55: 28. Wire Harness Set (14B-F2590-70)
Page 56 and 57: NOTICEWhen the oil catcher tank is
Page 58 and 59: Installing ECU:1. Cut the shaded ar
Page 60 and 61: • Map select switches Map 1 and M
Page 62 and 63: NOTICEDo not connect the coupler fo
Page 64 and 65: 30. ACM Set (14B-F1400-70)Parts Lis
Page 66 and 67: EngineTo be tightened Part No. Part
Page 68 and 69: EngineNUT, RING XCYLINDERHEADEX. PI
Page 74 and 75: ChassisTo be tightened Part No. Par
Page 76 and 77: Tightening the Cylinder HeadTighten
Page 78 and 79: - 75 -
Page 80 and 81: 5 YZF-R1 Wiring Diagram- 77 -

English - Yamaha-Racingparts.com

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?