BCP-8 Hydronic Manual - Weil-McLain

More documents

Recommendations

Info

14SYS=168 F OD=45 FTGT=172 FABC ---- LOBOILERMENU------ SETTINGS ------Season Winter 135 FSet Point 135 FEMS Set Point135 FMin Return 110 FBACK SELECT---- MAINTENANCE ----UnitFPresent Time12:30PBACK SELECT<strong>BCP</strong>-8W V1.00Outdoor resetDay/Night ScheduleDHW ParallelBACK SELECTSys=120 F10:00AMBACK NEXT--- SENSOR TRIM ----System Trim +0 FOutdoor Trim +0 FReturn Trim +0 FDHW Trim +0 FBACK SELECTARE YOU SURE?NoYesBACK SAVEdown the Menu button for overthree seconds.settings the Program/Run Switchmust be set to Program.--- SENSOR FAULT ---Stages OnStages OffBACK SAVE--- CONTROL LOGIC---PIDOSSBACK SAVE------ SEQUENCE -------Lo/Hi/Lo/HiLo/Lo/Hi/HiBACK SAVE------ STAGING ------Multiple OutputsSingle OutputBACK SAVE-- TOTAL BOILERS --8[ ]BACK SAVE-- BOILER OUTPUT --NonePumpValveBACK SAVE--- BURNER TYPE ----On/Off2-Stage3-Stage4-StageBACK SAVE---- CONTROL MODE ---Outdoor ResetSet PointEMS 4-20mABACK SAVE---- DISPLAY UNIT ---FCBACK SAVE EMS 4mA SET POINT100 F[ ]BACK SAVEEMS 20mA SET POINT170 F[ ]BACK SAVE---- DHW PIPING ---ParallelPrimary/SecondaryBACK SAVE--DHW PUMP OUTPUT--NoYesBACK SAVE--COMB. AIR OUTPUT--NoYesBACK SAVE-- EXTERNAL INPUT -ShutdownTstatSetbackBACK SAVE
-- EMS SET POINT --140 FBACK SAVE----- SET POINT -----140 F[ ]BACK SAVESYS=168 F OD=45 FTGT=172 FABC ---- LOBOILERMENU----- SETTINGS ------Season Winter 135 FSet Point 135 FEMS Set Point135 FMin Return 110 FBACK SELECT---- MIN RETURN ----120 F[ ]BACK SAVE---- RETURN LAG ----2min[ ]BACK SAVE- SYSTEM SETTINGS -Setback0 FRun-On2minPump Exercise OffBACK SELECT--- PUMP EXERCISE --OffOnBACK SAVE---- SEASON ---WinterSummerBACK SAVE-- OUTDOOR RESET -Reset Ratio 7Target Offset +0 FOutdoor Cutoff 65 FMin.Target 120 FMax.Target 120 FBACK SELECT---- MAX TARGET ----200 F[ ]BACK SAVE---- MIN TARGET ----140 F[ ]BACK SAVE-- OUTDOOR CUTOFF --60 F[ ]BACK SAVE-- TARGET OFFSET ---+0 F[ ]BACK SAVE -- DHW SETTINGS ---DHW Temp. 120 FDHW Prior Tmr 60minDHW Set Point120 FDHW Diff. 5 FBACK SELECT------ SETBACK -------0 F[ ]BACK SAVE------- RUN-ON -------2min[ ]BACK SAVE---- RESET RATIO ---Custom1(8.00 OD:1.00 SYS)2(4.00 OD:1.00 SYS)3(3.00 OD:1.00 SYS)4(2.00 OD:1.00 SYS)5(1.50 OD:1.00 SYS)6(1.25 OD:1.00 SYS)7(1.00 OD:1.00 SYS)8(1.00 OD:1.25 SYS)9(1.00 OD:1.50 SYS)10(1.00 OD:2.00 SYS)11(1.00 OD:3.00 SYS)12(1.00 OD:4.00 SYS)BACK SAVE-- SET SYS TEMP.1 -100 F[] BACK SAVE-- AT OD TEMP.1 ---70 F[] BACK SAVE-- SET SYS TEMP.2 -170 F[ ]BACK SAVE-- AT OD TEMP.2 ---0 F[ ]BACK SAVEDHW PRIORITY TIMER2min[ ]BACK SAVE-- DHW SET POINT --140 F[ ]BACK SAVEDHW DIFFERENTIAL10 F[] BACK SAVE15
Page 3 and 4: LEDs indicateassociated relay’s s
Page 5 and 6: The BCP-8W has multiple operating m
Page 7 and 8: saving features and give more comfo
Page 9 and 10: Immersion Heating System SensorImme
Page 11 and 12: ProveDry ContactSetbackDry ContactT
Page 13: ENCLOSEDENERGYMANAGEMENTEQUIPMENTEX
Page 17 and 18: Can be accessed by holding down the
Page 19 and 20: Hold Button: MENU//..../Burner Type
Page 21 and 22: Button: MENU/Season The MessageSumm
Page 23 and 24: every 1.5 degree change in the Outd
Page 25 and 26: -- STANDBY DELAY --10minHold Button
Page 27 and 28: Boost to 190 F". ------ BOOST PERIO
Page 29 and 30: can control the primary system pump
Page 31 and 32: System Temp Outdoor Temp Sys=155 F
Page 33 and 34: Check the sensor is connected and t
Page 35 and 36: SYS=168 F OD=45 FTGT=172 FABC ----
Page 37: -- SET SYS TEMP.1 - -- SET SYS TEMP

BCP-8 Hydronic Manual - Weil-McLain

Create successful ePaper yourself

Delete template?

Save as template?