BCP-8 Hydronic Manual - Weil-McLain

More documents

Recommendations

Info

Hold Button: MENU/The Maintenance menu gives access to sensor and output trimmings in addition to viewingTo be able to change the BCP-8W settings the Program/Run Switch must be setto Program. The switch is located under the Enclosure Wiring Cover for security.The Enclosure Wiring Cover can be securely closed using a padlock.---- MAINTENANCE ----UnitFPresent Time12:30PBACK SELECT°°°°°FHold Button: MENU//System TrimHold Button: MENU//Outdoor TrimHold Button: MENU//Return TrimHold Button: MENU//DHW Trim calibration. However, sometimes it may be desirable to make small adjustments to thedisplayed value. Hold Button: MENU/The BCP-8W provides users with a graphical history of the System, Outdoor, DHW, and Returnsensors for the previous 24 hours. The temperatures are sampled every 12 minutes. That is,readings of temperatures are recorded and stored every 12 minutes for the last 24 hours. and read the upper left temperature. you will be able to view the Outdoor Temperature History, then, the Return Historyfollowed by the DHW History.Hold Button: The BCP-8W display layout provides a variety of information that gives an immediatepicture of the operation status. The display shows four heating boilers at a time. Thetwo middle buttons scrolls the screen to view any additional boilers. Moreover, all theinformation is brightly displayed. It can be viewed in brightly or dimly lit rooms. functionality is displayed on a dark background on the screen's bottom line. displays the Target Set Point. If a Return sensor was connected, the Target display willbe alternating its value with the Return temperature. When the control is to display astatus message, the message will replace Target and Return temperatures. See DisplayMessages on page 1.--- SENSOR TRIM ----System Trim +0 FOutdoor Trim +0 FReturn Trim +0 FDHW Trim +0 FBACK SELECTSys=120 F10:00AMBACK NEXTBCP-8W V1.00Outdoor resetHeating-BreakOnRiseDay/Night ScheduleDHW ParallelBACKNEXT8 X On/OffPID,Fault Stgs OffBACKNEXT30
System Temp Outdoor Temp Sys=155 F OD=58 F Message Display LineDHW all (200 F) DE GH JK Units and theirHI HI LO ----StatusBOILERMENUButton functions Standby. Standby. Boiler Pumps are being controlled by the BCP-8W. The BCP-8W normal display layout reserved the second line for message indications. The following is a list of the most common whichever is lower. 31
Page 3 and 4: LEDs indicateassociated relay’s s
Page 5 and 6: The BCP-8W has multiple operating m
Page 7 and 8: saving features and give more comfo
Page 9 and 10: Immersion Heating System SensorImme
Page 11 and 12: ProveDry ContactSetbackDry ContactT
Page 13 and 14: ENCLOSEDENERGYMANAGEMENTEQUIPMENTEX
Page 15 and 16: -- EMS SET POINT --140 FBACK SAVE--
Page 17 and 18: Can be accessed by holding down the
Page 19 and 20: Hold Button: MENU//..../Burner Type
Page 21 and 22: Button: MENU/Season The MessageSumm
Page 23 and 24: every 1.5 degree change in the Outd
Page 25 and 26: -- STANDBY DELAY --10minHold Button
Page 27 and 28: Boost to 190 F". ------ BOOST PERIO
Page 29: can control the primary system pump
Page 33 and 34: Check the sensor is connected and t
Page 35 and 36: SYS=168 F OD=45 FTGT=172 FABC ----
Page 37: -- SET SYS TEMP.1 - -- SET SYS TEMP

BCP-8 Hydronic Manual - Weil-McLain

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?