Shire Owners' Manual (11 Build) 70 & 90 (PDF) - EP Barrus

More documents

Recommendations

Info

SECTION 2 - Engine IdentificationPlease quote the engine identification number during any enquiry or when orderingspare parts.This is found engraved into the brass plate, on top of the engine rocker cover andstamped to the crankcase above the starter motor.An example of the engine identification plate is as follows:Figure 2-1: Engine Identification BadgeNote: There are a number of optional extras that may be fitted to an engine for particularcustomer’s engine that are not listed here.A list of common item service part numbers can be found in Shire service parts, inSection 6.RDG6039258 Issue 5 Shire 70 & 90 Owners Manual Page 10 of 48
SECTION 3 - Installation1. Ventilation• All internal combustion engines radiate heat and require cool, clean air for completecombustion purposes.• Please ensure that adequate engine room ventilation is provided, by fitting at leasttwo vents of an aperture of not less than 15,000 mm 2 each, (24 in 2 ).An allowance must be made for any grills or louvres placed in the airflows andgenerally, an increase of 25% in area is sufficient to overcome any restrictionproblems.2. Engine Beds• These should be a minimum of 10mm thick and extended rearward and be weldedto the hull and forward to the bulkhead. There must be webs or gussets welded inplace to prevent flexing.3. Cooling System• Ensure pipe work to and from the skin tanks is of sufficient bore. A minimum of45mm (1½") is recommended. Ensure tight bends and elbows are avoided or kept toa minimum.4. Skin Tanks• The ideal skin tank internal thickness should be not less than 50mm and not exceed75mm; the table below will indicate a suitable size however volume will notcompensate for lack of surface area. It should be recognised that fitting a largecalorifier would increase the theoretical cooling capacity only until it is up totemperature. It is unlikely that a boat on the inland waterways will operate at fullpower for more than short periods. The engine cooling water outlets are on the righthand (starboard) side of the engine.RDG6039258 Issue 5 Shire 70 & 90 Owners Manual Page 11 of 48
Page 1 and 2: SHIRE CANAL BOAT MANUALFOR THE FOLL
Page 3 and 4: Declaration of Conformity for Recre
Page 5 and 6: CONDITIONS THAT MUST BE MET IN ORDE
Page 7 and 8: SECTION 8 - WIRING DIAGRAMS........
Page 9: • If charging the battery; ensure
Page 13 and 14: Figure 3-2: Shire 70 Header Tank Co
Page 15 and 16: Figure 3-5: Correct Anti-Vibration
Page 17 and 18: 10. ElectricsWARNING:The blue link
Page 19 and 20: test procedure.14. Coolant• Yanma
Page 21 and 22: • The maximum domestic battery ba
Page 23 and 24: 3. Stopping Procedure• Move speed
Page 25 and 26: SECTION 5 - Service Procedure1. Eng
Page 27 and 28: PRM 260 gearbox filler circled in t
Page 29 and 30: 9. Fuel System Bleeding• Ensure t
Page 31 and 32: • Remove the belt.• Hold the be
Page 33 and 34: SECTION 6 - Service PartsShire 70Sp
Page 35 and 36: SECTION 8 - Wiring Diagrams1. Engin
Page 37 and 38: 3. Engine Wiring Diagram, Shire 90
Page 39 and 40: 5. Deluxe Panel Wiring Diagram (24
Page 41 and 42: 6. VDO 7KW Wiring diagram and overa
Page 43 and 44: SECTION 9 - General Arrangement Dra
Page 45 and 46: 3. Shire 11 909685022117 x 6.DETAIL
Page 47 and 48: SECTION 10 - Dealer ListArea Compan

Shire Owners' Manual (11 Build) 70 & 90 (PDF) - EP Barrus

Create successful ePaper yourself

Delete template?

Save as template?