Shire Owners' Manual (11 Build) 70 & 90 (PDF) - EP Barrus

More documents

Recommendations

Info

2. Air Filter Check & ChangeCAUTION:WEAR DISPOSABLE GLOVES AND BEWARE OF HOT OIL AND ENGINE BLOCK.REMOVE THE IGNITION KEY BEFORE WORKING IN ENGINE COMPARTMENT.• Release the two spring clips, pull off the end cover to reveal the filter element. Theelement simply pulls out. Note: the Shire 90 has an inner safety element fitted.• The air filter element is constructed from pleated paper; inspect it closely for dust ordirt. The air filter cannot be cleaned and must be replaced when dirty. The enginerequires clean unrestricted air to run efficiently, failure to maintain the air filter couldresult in smoke, increased fuel consumption and ultimately engine damage.• To fit the new element, slide the open end of the filter element into the main body;gently push the element home until fully seated. Refit the end cover.3. Gearbox Oil ChangeCAUTION:WEAR DISPOSABLE GLOVES AND BEWARE OF HOT OIL AND GEARBOX CASING.REMOVE THE IGNITION KEY, BEFORE WORKING IN ENGINE COMPARTMENT.• Change the gearbox oil while it is still hot. (Please refer to gearbox manual for moreinformation).• Remove the plug from the gearbox drain pump; this is the smaller of the two pumps(6mm Allen key).• Pump contents in a suitable container (not less than 2.2 litres).• Refill the gearbox with oil to the upper mark on the dipstick. Screw dipstick in fully toestablish level. The gearbox uses the same grade of oil as the engine.• Do not overfill gearbox as this can damage the internal components.RDG6039258 Issue 5 Shire 70 & 90 Owners Manual Page 26 of 48
PRM 260 gearbox filler circled in the picture below.4. Disposal of Oil and Related Items• Please dispose of used oil and oil filters safely with due regard for the environment,and take to your local waste oil disposal point.• Do not allow oil or contaminated parts enter the inland waterway system.5. Primary Fuel Filter Water DrainCAUTION:WEAR DISPOSABLE GLOVES.REMOVE THE IGNITION KEY BEFORE WORKING IN ENGINE COMPARTMENT• Place a small drain bowl under the fuel filter/water separator drainpipe and loosenthe drain screw located on the bottom of the filter.• Drain off any water.• After accumulated water has been drained, close the drain screw.• It is unlikely the complete fuel system will require bleeding.• Start and run engine for 5 minutes.• Check that the drain union is tight and that there are no leaks.• Note: the boat builder may have fitted an additional water trap in the fuel systembefore the engine.RDG6039258 Issue 5 Shire 70 & 90 Owners Manual Page 27 of 48
Page 1 and 2: SHIRE CANAL BOAT MANUALFOR THE FOLL
Page 3 and 4: Declaration of Conformity for Recre
Page 5 and 6: CONDITIONS THAT MUST BE MET IN ORDE
Page 7 and 8: SECTION 8 - WIRING DIAGRAMS........
Page 9 and 10: • If charging the battery; ensure
Page 11 and 12: SECTION 3 - Installation1. Ventilat
Page 13 and 14: Figure 3-2: Shire 70 Header Tank Co
Page 15 and 16: Figure 3-5: Correct Anti-Vibration
Page 17 and 18: 10. ElectricsWARNING:The blue link
Page 19 and 20: test procedure.14. Coolant• Yanma
Page 21 and 22: • The maximum domestic battery ba
Page 23 and 24: 3. Stopping Procedure• Move speed
Page 25: SECTION 5 - Service Procedure1. Eng
Page 29 and 30: 9. Fuel System Bleeding• Ensure t
Page 31 and 32: • Remove the belt.• Hold the be
Page 33 and 34: SECTION 6 - Service PartsShire 70Sp
Page 35 and 36: SECTION 8 - Wiring Diagrams1. Engin
Page 37 and 38: 3. Engine Wiring Diagram, Shire 90
Page 39 and 40: 5. Deluxe Panel Wiring Diagram (24
Page 41 and 42: 6. VDO 7KW Wiring diagram and overa
Page 43 and 44: SECTION 9 - General Arrangement Dra
Page 45 and 46: 3. Shire 11 909685022117 x 6.DETAIL
Page 47 and 48: SECTION 10 - Dealer ListArea Compan

Shire Owners' Manual (11 Build) 70 & 90 (PDF) - EP Barrus

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?