Shire Owners' Manual (11 Build) 70 & 90 (PDF) - EP Barrus

More documents

Recommendations

Info

Alternative mounting position ifengine compartment space isrestricted.Normal mounting position.Figure 3-6: Anti-Vibration Mount Installation Points9. Engine Alignment• The gearbox output shaft flange and propeller shaft input flange must be almostperfectly aligned. A maximum of 0.05mm (0.002") misalignment in any plane isacceptable. Ensure alignment is rechecked after the first 4 hours of running, at theend of the first month and annually thereafter.• If the engine is out of alignment it will result in excessive vibration and possibledamage to the stern tube and propeller shaft.• Boats that are fitted with fully flexible drive couplings should still have the engine andshaft alignment as close as possible. A dummy shaft may be required for thispurpose.(Note: some types of flexible shaft couplings require the input and output to bemisaligned, check with the coupling manufacturer’s installation instructions).RDG6039258 Issue 5 Shire 70 & 90 Owners Manual Page 16 of 48
10. ElectricsWARNING:The blue link wire must be removed when the domestic battery positive terminal lead hasbeen connected to the terminal post.Do not run the engine without this wire in place or without the domestic battery positive leadconnected otherwise alternator damage will occur.If the engine is going to run for more than 1 hour with the blue link wire in place, removedomestic alternator drive belt to prevent alternator damage.• Do not attach any part, hose or cable to the engine wiring harness. There is awarning label attached to the harness to remind you of this.• Connect the wiring extension harness multi plug to the panel plug, and the other endto the engine.• Connect the start battery positive cable to the engine starter motor solenoid terminal.• Starter motor battery cable size to be a minimum of 50mm 2 .• Shire 70 - Connect the domestic battery positive cable to the 160 Amp Alternator“Pos out” terminal (see wiring diagram). This ensures that the 50A alternatorcharges the start battery and the 160A alternator charges the domestic battery. Twinalternators remove the requirement for a split charging system or relay.• Shire 90 – Connect the domestic battery positive cable to the 120Amp alternator B+terminal (see wiring diagram). This ensures that the 110Amp charges the startbattery.• The blue link wire between the 120A Alternator B+ terminal or 160A “pos out”terminal and the starter motor solenoid must be removed when the domestic batteryis connected.• Shire 70, cable will need to be manufactured locally and fitted between the lower160A alternator “pos out” terminal and the domestic battery positive terminal. Cableshould have a minimum cross sectional area of 50mm 2 (193amp capacity).• Shire 90, cable will need to be manufactured locally and fitted between the upper120A alternator B+ terminal and the domestic battery positive terminal. Cable shouldhave a minimum cross sectional area of 35mm 2 (135 amp capacity).• Both negative battery terminals can be connected to a common earth point.RDG6039258 Issue 5 Shire 70 & 90 Owners Manual Page 17 of 48
Page 1 and 2: SHIRE CANAL BOAT MANUALFOR THE FOLL
Page 3 and 4: Declaration of Conformity for Recre
Page 5 and 6: CONDITIONS THAT MUST BE MET IN ORDE
Page 7 and 8: SECTION 8 - WIRING DIAGRAMS........
Page 9 and 10: • If charging the battery; ensure
Page 11 and 12: SECTION 3 - Installation1. Ventilat
Page 13 and 14: Figure 3-2: Shire 70 Header Tank Co
Page 15: Figure 3-5: Correct Anti-Vibration
Page 19 and 20: test procedure.14. Coolant• Yanma
Page 21 and 22: • The maximum domestic battery ba
Page 23 and 24: 3. Stopping Procedure• Move speed
Page 25 and 26: SECTION 5 - Service Procedure1. Eng
Page 27 and 28: PRM 260 gearbox filler circled in t
Page 29 and 30: 9. Fuel System Bleeding• Ensure t
Page 31 and 32: • Remove the belt.• Hold the be
Page 33 and 34: SECTION 6 - Service PartsShire 70Sp
Page 35 and 36: SECTION 8 - Wiring Diagrams1. Engin
Page 37 and 38: 3. Engine Wiring Diagram, Shire 90
Page 39 and 40: 5. Deluxe Panel Wiring Diagram (24
Page 41 and 42: 6. VDO 7KW Wiring diagram and overa
Page 43 and 44: SECTION 9 - General Arrangement Dra
Page 45 and 46: 3. Shire 11 909685022117 x 6.DETAIL
Page 47 and 48: SECTION 10 - Dealer ListArea Compan

Shire Owners' Manual (11 Build) 70 & 90 (PDF) - EP Barrus

Create successful ePaper yourself

Delete template?

Save as template?