Shire Owners' Manual (11 Build) 70 & 90 (PDF) - EP Barrus

More documents

Recommendations

Info

11. Belt AdjustmentCAUTION:REMOVE THE IGNITION KEY BEFORE WORKING IN ENGINE COMPARTMENT.• Depress the longest run of the drive belt to be checked. If the travel exceeds 15 -20mm using hard finger pressure, the belt needs re-tensioning.• Loosen the upper adjuster bolts on the alternator, and the lower mounting pivot nutand bolt, either pull out using hand pressure or use the tensioning screw, dependingon which alternator is fitted.• Pull the alternator away from the engine to tighten the belt.• Hold the alternator in position and re-tighten all the bolts.Note:1 – If the belts are over tightened alternator bearing failure will occur.2 – Shire 90, 110Amp and 120Amp alternator belt is self-adjusting.12. Belt Maintenance• Do not allow oil to contact the belt, oil attacks the construction of the belt, reducesthe drive efficiency and will ultimately cause it to fail prematurely.• Replace the belt if it cracks, splits, or as the adjustment nears the limit of its travel.• Note: Some boat builders may remove one or more of the alternators during theinstallation of the engine. It is essential that when the alternators are refitted that thealignment is perfect or premature belt wear will occur.13. Belt ReplacementCAUTION:REMOVE THE IGNITION KEY BEFORE WORKING IN ENGINE COMPARTMENT.Shire 70:• Ensure that you have the correct belts before starting this procedure. Somecustomers may have engines fitted with non standard optional alternators which maynot have the standard belts listed. Make a note of the belt sizes on delivery.• Loosen the top adjuster bolts, and the lower mounting pivot nut and bolt.• Push the alternator towards the engine to loosen the belt.RDG6039258 Issue 5 Shire 70 & 90 Owners Manual Page 30 of 48
• Remove the belt.• Hold the belt in position over the top alternator pulley, rotate the engine, if required,by hand, to guide the new belt into the “vee”.• Re - tension the belt as above.Shire 90:• Insert a ½” drive ‘T’ bar into the highlighted square area of the automatic tensioner.• Pull lever bar in anti-clockwise direction to slacken off the belt.• Remove belt.• Pull lever bar anti-clockwise again and re-fit belt.• Check that the belt is fitted correctly into all of the pulley grooves.• Note the tensioner brace bar will need to be removed before the old belt can beremoved, and then replaced after the new belt has been fitted.120 Amp altAdjuster110 Amp altRDG6039258 Issue 5 Shire 70 & 90 Owners Manual Page 31 of 48
Page 1 and 2: SHIRE CANAL BOAT MANUALFOR THE FOLL
Page 3 and 4: Declaration of Conformity for Recre
Page 5 and 6: CONDITIONS THAT MUST BE MET IN ORDE
Page 7 and 8: SECTION 8 - WIRING DIAGRAMS........
Page 9 and 10: • If charging the battery; ensure
Page 11 and 12: SECTION 3 - Installation1. Ventilat
Page 13 and 14: Figure 3-2: Shire 70 Header Tank Co
Page 15 and 16: Figure 3-5: Correct Anti-Vibration
Page 17 and 18: 10. ElectricsWARNING:The blue link
Page 19 and 20: test procedure.14. Coolant• Yanma
Page 21 and 22: • The maximum domestic battery ba
Page 23 and 24: 3. Stopping Procedure• Move speed
Page 25 and 26: SECTION 5 - Service Procedure1. Eng
Page 27 and 28: PRM 260 gearbox filler circled in t
Page 29: 9. Fuel System Bleeding• Ensure t
Page 33 and 34: SECTION 6 - Service PartsShire 70Sp
Page 35 and 36: SECTION 8 - Wiring Diagrams1. Engin
Page 37 and 38: 3. Engine Wiring Diagram, Shire 90
Page 39 and 40: 5. Deluxe Panel Wiring Diagram (24
Page 41 and 42: 6. VDO 7KW Wiring diagram and overa
Page 43 and 44: SECTION 9 - General Arrangement Dra
Page 45 and 46: 3. Shire 11 909685022117 x 6.DETAIL
Page 47 and 48: SECTION 10 - Dealer ListArea Compan

Shire Owners' Manual (11 Build) 70 & 90 (PDF) - EP Barrus

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?