Site Specifications for the VITROS® 5,1 FS Chemistry System and ...

Site Specificationsfor theVITROS ® 5,1 FS Chemistry Systemand VITROS ® 4600 Chemistry SystemPublication No. J398972014-03-01Supersedes J398972012-11-21

PLEASE NOTEThe information contained herein is based on the experience and knowledge relating to the subject mattergained by Ortho-Clinical Diagnostics, Inc. (OCD) prior to publication.No patent license is granted by this information.OCD reserves the right to change this information without notice, and makes no warranty, expressed orimplied, with respect to this information. OCD shall not be liable for any loss or damage, includingconsequential or special damages, resulting from any use of this information, even if loss or damage iscaused by the negligence or other fault of OCD.This equipment includes parts and assemblies sensitive to damage from electrostaticdischarge. Use caution to prevent damage during all service procedures.Table of ContentsDescriptionPageElectrical Power Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Electrical Specifications for the 5,1 and 4600 Systems . . . . . . . . . . . . . . . . . . . . . . . . 4Electrical Specifications for the Supplied PRINTER . . . . . . . . . . . . . . . . . . . . . . . . . . 5Electrical Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6RECEPTACLE Location Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Environmental Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Networking Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Requirements at Customer Site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10Shipping Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11Specifications for the System and the PRINTER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12Specifications for the 5,1 and 4600 HEAT REJECTION PLENUM . . . . . . . . . . . . . . 132 2014-03-01 – J39897

Section 1: Electrical Power RequirementsElectrical Power RequirementsAC Power QualityThe VITROS ® 5,1 FS Chemistry System (hereafter referred to as the 5,1) and the VITROS ® 4600 Chemistry System(hereafter referred to as the 4600) are designed to perform satisfactorily with reasonable disturbances and voltagetolerance to the ac power. The quality and reliability of the power source is often dependent on the geographiclocation of the site. Some sites, where power quality is exceptionally poor, may require special power conditioningequipment to ensure that the tolerances are maintained within acceptable limits. Some models ofUNINTERRUPTIBLE POWER SUPPLIES (UPS) are recommended as optional equipment for use with VITROS ®Systems, and may be purchased from the Distribution Center. For additional information, see the UPS User Guidelocated at: http://apps.orthoclinical.com/notes/contentpages/techdoc.aspx?view=USOTHER&culture=en-usStatic ElectricityThe System should be adequately grounded to prevent the effects of static charges generated. Static problems canalso be reduced by ensuring that the relative humidity of the room is maintained above 30 percent. Special anti-staticfloor pads can be purchased and positioned where the operator is required to make contact with the instrument.Electromagnetic InterferenceSeveral types of electrical interference may be indigenous to the site location and may require special filtering toprevent malfunctions in the 5,1 or 4600 systems. If interference is suspected to be a problem, shielding may berequired, or filtering of the ac line power to the site may be necessary.Cellular phones, two-way pagers, and other RF transmitting devices should not be used within 1 m of the 5,1 or 4600Systems.2014-03-01 – J39897 3

Section 2: Electrical Specifications for the 5,1 and 4600 SystemsInput Voltage* 200 to 240 VInput Frequency Limits 50 - 60 Hz 2 HzPowerOperating (Normal) 1225 WattsMaximum Current 15APOWER CORD 4 m (13 ft)PLUG TypeNorth America IEC 320 to NEMA L6-20PContinental Europe IEC 320 to CEE7 “Schuko”OtherAs required by local electrical codesCIRCUIT Type Dedicated with Isolated GroundRECEPTACLE TypeNorth America NEMA L6-20RContinental Europe CEE7 “Schuko”OtherAs required by local electrical codes* When measuring supply voltage:• Use a MULTIMETER.• Check a number of times and use the average of the values.• Wait a minimum of 5 minutes between checks.• The difference between the values should not be more than 6%.ImportantIf an optional UPS is to be installed, make certain thatthe correct receptacle is installed in the lab.UPS Rating Amps Receptacle Type3 KVA 20 A L6-20R**5 KVA 30 A L6-30R**** or an equivalent to meet local electrical codes208 V Check between Voltage60 Hz L1 - L2 190 - 220 V ACL1 - SAFETY GROUND 113 - 127 V ACL2 - SAFETY GROUND 113 - 127 V AC240 V Check between Voltage60 Hz L1 - L2 226 - 254 V ACL1 - SAFETY GROUND 113 - 127 V ACL2 - SAFETY GROUND 113 - 137 V ACNoteCEE7 “Schuko” plug may be supplied, either straight or right angle.4 2014-03-01 – J39897

Electrical Specifications for the Supplied PRINTERSection 3: Electrical Specifications for the Supplied PRINTERImportantThe following information is only applicable to PRINTERS supplied by OCD. If the PRINTER is being supplied bythe customer, refer to the manufacturer’s PRINTER manual for the electrical specifications.1 RECEPTACLErequired3-wire, 120 V AC, polarized, SAFETY GROUND,maximum distance of 182.7 cm (72 in.) from eachside of the system.DedicatedCIRCUIT Type120 V Check between Voltage60 Hz N - L1 102 - 132 V AC15 amperes L1 - SAFETY GROUND 102 - 132 V ACN - SAFETY GROUND Less than 1 V ACDetach 1NEMA 5-15RSAFETYGROUNDL1Npolarized powerRECEPTACLEE002_1331ACAE002_1331AC2014-03-01 – J39897 5

Section 4: Electrical RequirementsTension200 to 240 VoltsIntensity15.0 Amps MaximumFrequency50 / 60 HzConsumption (nominal) 3.0 kVAMax Power3000 WNumber of socket-outlet 1, plus 1 for printerProtection against micro cuts Yes(Momentary power interruption)Maximum timeTolerant of missing one full cycle of 50 Hz(20 milliseconds)System tolerance to electrical 180 to 264 VAC 48-62 Hz extremevariation6 2014-03-01 – J39897

Section 5: RECEPTACLE Location SpecificationsRECEPTACLE Location SpecificationsSpecifications for PRINTER POWER andNETWORK CONNECTIONReferenceQ (heightfrom floor)S (printerpower)T(Network)Description30.5 cm (12 in.) minimum61.0 cm (24 in.) maximum2.9 m (8 ft. 10 in.) maximum5.3 m (17 ft. 6 in.) maximumSpecifications for the System onlyReferenceQ (heightfrom floor)R (systempower)Description30.5 cm (12 in.) minimum61.0 cm (24 in.) maximum1.98 m (6 ft. 6 in.) maximumDetach 22014-03-01 – J39897 7

Section 6: Environmental SpecificationsAcoustic Noise Level 61 dbThermal CharacteristicsOn 4187 Btu/hrDetach 3Maximum altitude: 2438 m (8000 ft.)This product has been evaluated and is suitable only for Pollution Degree II and Insulation Category II.Additional Requirements for the VITROS ® 5,1 and VITROS ® 4600 HEAT REJECTION PLENUMIf the customer chooses to purchase and use the optional Heat Rejection Plenum, the EXHAUST SYSTEM andDUCT must be installed by the customer.SpecificationsAir Capacity7.1 - 9.9 cubic metres (250 - 350 cubic ft.) per minute259 - 366 metres (850 - 1200 ft.) per minuteDUCT20.5 cm (8 in.) flexible AIR DUCT and attaching hardwareAir Flow - Ventilation System7.1 - 9.9 cubic metres (250 - 350 cubic ft.) per minute at 5.1 mm (0.2 in.) of water vacuum8 2014-03-01 – J39897

Section 7: Networking SpecificationsNetworking SpecificationsThe requirements for e-Connectivity network connection are located in the e-Connectivity® Network ConnectionSpecifications and Network Form located on-line at:http://apps.orthoclinical.com/notes/contentpages/techdoc.aspx?view=USSPECSThe customer must complete the form and return it to Ortho-Clinical Diagnostics.ImportantAll requirements for lab network connections must be completed before installation of the analyzer(s).2014-03-01 – J39897 9

Section 8: Requirements at Customer SiteTELEPHONEAir FlowEntrance to the room wherethe System will be installedA TELEPHONE located so that the user can movearound the System must be available.No air flow within 3.0 m (10 ft) of the System.Minimum width of 81.3 cm (32 in.)LAB COMPUTER Interface See the Interface Specification section of theOperator’s Manual.Network Connection Refer to the Networking Specifications on page 9.Floor Loading 322 kg/m 2 (65 lb./ft 2 )10 2014-03-01 – J39897

Shipping SpecificationsSection 9: Shipping SpecificationsShipping SpecificationsReferenceDescriptionA 274.3 cm (108 in.)B 110.5 cm (43.5 in.)C 161.3 cm (63.5 in.)D 215.9 cm (85 in.) *Weight 811.9 kg (1790 lb)* Minimum overhead clearance required for unpacking.Detach 42014-03-01 – J39897 11

Section 10: Specifications for the System and the PRINTERSystem Specifications Supplied PRINTER Specifications ****Reference Description Reference DescriptionA 233.7 cm (92 in.) * J 40.0 cm (15.7 in.)B 83.8 cm (33 in.) K 51.3 cm (20.2 in.)C 132.1 cm (52 in.) L 34 cm (13.4 in.)D 205.7 cm (81 in.) M 61 cm (24 in.)Weight 612.4 kg (1350 lb) Weight 19.7 kg (43.5 lb.)* 264.7 cm (104.2 in.) if AT Accessory is installed. PortPrinter LanguageInstallation Specificationsfor the System onlyUSB Version (TBD)Post ScriptInstallation Specificationsfor the Supplied PRINTER ****Reference Description Reference DescriptionE 76.2 cm (2 ft 6 in.) N 17.8 cm (7 in.)F 76.2 cm (2 ft 6 in.) O 45.7 cm (18 in.)G 30.5 cm (12 in.) ** P 61.0 cm (24 in.)H 4.3 m (14 ft. ) *** **** If the PRINTER is being supplied by theQ 76.2 cm (30 in.)customer, refer to the manufacturer’s PRINTERmanual for any specifications.** 91 cm (36 in.) if SEISMIC ANCHORAGES, ATAccessory Kit if installed from the rear or otherwise30.5 cm (12 in.) if installed from the front, or HEATREJECTION PLENUM are to be installed.*** 4.6 m (15 ft.) if AT Accessory is installed.12 2014-03-01 – J39897

Specifications for the 5,1 and 4600 HEAT REJECTION PLENUMSection 11: Specifications for the 5,1 and 4600 HEAT REJECTIONPLENUMDetach 5HEAT REJECTION PLENUMSpecificationsReference DescriptionA 107.1 cm (42.2 in.)B 77.5 cm (30.5 in.)C 38.7 cm (15.2 in.)D 17.7 cm (7.0 in.)2014-03-01 – J39897 13

14 2014-03-01 – J39897

Ortho Clinical Diagnostics50 - 100 Holmers Farm WayHigh WycombeBuckinghamshireHP12 4DPUnited KingdomOrtho-Clinical Diagnostics, Inc.100 Indigo Creek DriveRochester, NY 14626