6. SetupSetup should occur before us<strong>in</strong>g this controller, <strong>to</strong> set <strong>the</strong> Input type, Alarm action, Control action, etc.accord<strong>in</strong>g <strong>to</strong> <strong>the</strong> users’ conditions.Default values: Input (K, -200 <strong>to</strong>1370 ), Alarm 1 (No alarm action), Reverse (Heat<strong>in</strong>g) actionIf <strong>the</strong> users’ specification is <strong>the</strong> same as <strong>the</strong> default value of <strong>the</strong> <strong>ACS</strong>-<strong>13A</strong>, it is not necessary <strong>to</strong> set up <strong>the</strong>controller. Proceed <strong>to</strong> Chapter “7. Sett<strong>in</strong>gs”.Turn <strong>the</strong> power supply <strong>to</strong> <strong>the</strong> <strong>ACS</strong>-<strong>13A</strong> ON.After <strong>the</strong> power is turned on, <strong>the</strong> PV display <strong>in</strong>dicates <strong>the</strong> <strong>in</strong>put type, and <strong>the</strong> SV display <strong>in</strong>dicates <strong>the</strong><strong>in</strong>put range high limit value (<strong>the</strong>rmocouple, RTD <strong>in</strong>put) or scal<strong>in</strong>g high limit value (DC <strong>in</strong>put) forapproximately 3 seconds. (Table 6-1)Dur<strong>in</strong>g this time, all outputs and <strong>the</strong> <strong>in</strong>dica<strong>to</strong>rs are <strong>in</strong> OFF status.Control will <strong>the</strong>n start and <strong>the</strong> PV display <strong>in</strong>dicates PV (process variable) and <strong>the</strong> SV display<strong>in</strong>dicates SV (set value). While control output OFF function is work<strong>in</strong>g, <strong>the</strong> PV display <strong>in</strong>dicates .(Indication depends on <strong>the</strong> selection dur<strong>in</strong>g “Output status selection when <strong>in</strong>put abnormal”.)(Table 6-1)KSensor <strong>in</strong>putJRSBETNPL-C (W/Re5-26)Pt100JPt100PV display SV display PV display SV display4 <strong>to</strong> 20mA DC0 <strong>to</strong> 20mA DC0 <strong>to</strong> 1V DC0 <strong>to</strong> 5V DC1 <strong>to</strong> 5V DC0 <strong>to</strong> 10V DCScal<strong>in</strong>g high limit valueBasic operation of sett<strong>in</strong>gsTo enter each sett<strong>in</strong>g mode, refer <strong>to</strong> respective sett<strong>in</strong>g modes.To set or select each sett<strong>in</strong>g item, use <strong>the</strong> or key, <strong>the</strong>n register <strong>the</strong> value with <strong>the</strong> key.6.1 Setup modeTo enter <strong>the</strong> Setup mode, press <strong>the</strong> key for approx. 3 seconds while hold<strong>in</strong>g down <strong>the</strong> key <strong>in</strong> <strong>the</strong>PV/SV display mode.Character Name, Function, Sett<strong>in</strong>g range Default valueInput type selection K (-200 <strong>to</strong> 1370 )• The <strong>in</strong>put type can be selected from <strong>the</strong>rmocouple (10 types), RTD (2 types), DCcurrent (2 types) and DC voltage (4 types), and <strong>the</strong> unit / can be selected as well.• When chang<strong>in</strong>g <strong>the</strong> <strong>in</strong>put from DC voltage <strong>to</strong> o<strong>the</strong>r <strong>in</strong>puts, remove <strong>the</strong> sensor connected<strong>to</strong> this controller first, <strong>the</strong>n change for <strong>the</strong> <strong>in</strong>put. If <strong>the</strong> <strong>in</strong>put is changed with <strong>the</strong> sensorconnected, <strong>the</strong> <strong>in</strong>put circuit may break.• (+) side <strong>in</strong>put term<strong>in</strong>al number of 0 <strong>to</strong> 5V DC, 1 <strong>to</strong> 5V DC, 0 <strong>to</strong> 10V DC differs fromthat of 0 <strong>to</strong> 1V DC.(+) side <strong>in</strong>put term<strong>in</strong>al number of 0 <strong>to</strong> 5V DC, 1 <strong>to</strong> 5V DC, 0 <strong>to</strong> 10V DC: 9(+) side <strong>in</strong>put term<strong>in</strong>al number of 0 <strong>to</strong> 1V DC: 10K -200 <strong>to</strong> 1370 K -320 <strong>to</strong> 2500K -200.0 <strong>to</strong> 400.0 K -320.0 <strong>to</strong> 750.0J -200 <strong>to</strong> 1000 J -320 <strong>to</strong> 1800R 0 <strong>to</strong> 1760 R 0 <strong>to</strong> 3200S 0 <strong>to</strong> 1760 S 0 <strong>to</strong> 3200B 0 <strong>to</strong> 1820 B 0 <strong>to</strong> 33007