BWH Manual (PDF) - INTRuST Neuroimaging Leadership Core

More documents

Recommendations

Info

10.3 MRI Acquisition Summary (Appendix 3)Qualification Phantom Scan Protocol:1. Localizer2. ASSET Calibration Scan3. INTRuST suggested DWI sequence4. INTRuST suggested Structural Scan Sequence (T1)5. INTRuST suggested Susceptibility Weighted Imaging sequence6. INTRuST suggested Proton Density Scan7. INTRuST suggested T2 scan sequence8. INTRuST suggested Resting State fMRIHuman Volunteer Scan Protocol for Calibration:1. Localizer2. ASSET Calibration Scan3. INTRuST suggested DWI sequence4. INTRuST suggested Structural Scan Sequence (T1)5. INTRuST suggested Susceptibility Weighted Imaging sequence6. INTRuST suggested Proton Density Scan7. INTRuST suggested T2 scan sequence8. INTRuST suggested Resting State fMRI (Subject should have eyes OPEN)Routine Phantom Scan Protocol:1. Localizer2. ASSET Calibration Scan3. BIRN fMRI Sequence (echo planar sequence)Subject Scanning Session for Clinical Trial:1. Localizer2. ASSET Calibration Scan3. INTRuST suggested DWI sequence4. INTRuST suggested Structural Scan Sequence (T1)5. INTRuST suggested Susceptibility Weighted Imaging sequence6. INTRuST suggested Proton Density Scan7. INTRuST suggested T2 scan sequence8. INTRuST suggested Resting State fMRI (Subject should have eyes OPEN)NOTE: The NLC will be supplying electronic protocols for installation to your local serviceengineer for your specific MRI system. This will ensure that you have the correct protocol foryour MRI scanner.If you have questions regarding these procedures, please contact: MJC@bwh.harvard.eduUse only the imported INTRuST sequences.
10.4 INTRuST Quality Assurance Guide for all Modalities (Appendix 4)* A more detailed version of the Quality Assurance guide will be sent out by the NLC. At thattime, we will ask you to physically replace this section (Appendix 4) of your INTRuST TechnicalProcedures Manual.Adjust brightness and contrast such that the background is visible in a gray color:Acceptable brightness and contrastBrain CoverageEven though image dimensions will be checked automatically, coverage might still be an issue.Check that the full brain (top-bottom, left-right and front-back) is in the MR image.ArtifactsGhosts: check for ghosting artifacts. You may have to adjust the brightness/contrast to makethem visible. Ghost images that are inside the brain are problematicGhosting
Page 1 and 2: MRI Technical Procedures ManualUpda
Page 3 and 4: What Institutions are participating
Page 5 and 6: 1. General InformationThe purpose o
Page 7 and 8: 3. Site QualificationNote: This is
Page 9 and 10: Example of sagittal image from high
Page 11 and 12: 5.4 Subject PositioningProper subje
Page 13 and 14: Subject ID: INTRuST_023_V_###Where
Page 15 and 16: Scan Information Log (Appendix 2).7
Page 17 and 18: 8. Full MRI Scan DescriptionsNOTE:
Page 19 and 20: • Images should be collected infe
Page 21 and 22: and should fully cover the cerebell
Page 23 and 24: 8.7 Resting State fMRI Scan8.7.1 Or
Page 25: 10. Appendices10.1 MRI Pre-Screenin
Page 29 and 30: MRI Scan Information LogINTRuST - M
Page 31: Scan #7: Resting State fMRIComplete
Page 35 and 36: Metal Artifact: In this example the
Page 37 and 38: T2W SPECIFIC QAIf multi-coil calibr
Page 39 and 40: 10.5 Data Transfer to the CNDA Data
Page 41: Finally, in the “Additional Notes

BWH Manual (PDF) - INTRuST Neuroimaging Leadership Core

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?